Abstract:In recent years, LC resonant sensors have gained widespread attention for their extensive applications in industries such as pharmaceutical storage and food transportation. A wireless passive sensor with a good sensing performance is proposed based on a GO/CNT−OH/Nafion nanocomposite. The sensor was fabricated via inkjet printing technology, and the surface morphology of the GO/CNT−OH/Nafion nanocomposite was characterized by SEM measurement. It is found that the MWCNTs support the GO layer and the hydrophobic chains of Nafion interact with the hydrophobic layer of GO, resulting in a larger cavity and hydrophilic surface of the entire material. This structure well reflects the fact that the mixing of MWCNTs and Nafion provides the entire material with a stronger water absorption. The experimental study shows that the proposed humidity sensor has a frequency variation of 103 kHz/%RH at low humidity (30–60% RH) and a sensitivity of 931 kHz/%RH at high humidity (60–95% RH), while the sensitivity value from 30–95% RH is 547 kHz/% RH. The response time and recovery time are 110 s and 115 s, respectively. In addition, the tests showed that the GO/CNT−OH/Nafion nanocomposite applied to the humidity sensor had a maximum humidity hysteresis of about 3% RH at 30–95% RH, the resonant frequency remained basically unchanged after 50 h of testing, and the whole sensor possessed a good stability. After conducting several repeated experiments, it was found that the resonant frequency error of the whole sensor was low and did not affect the overall sensing test, which proved the reproducible preparation of the sensor. Finally, the humidity-sensing mechanism of the proposed sensor was analyzed in this paper, and it was found that GO enhanced the hygroscopic properties of GO/CNT−OH/Nafion nanocomposite when it was supported by MWCNT-OH and included uniformly dispersed Nafion. Therefore, our proposed humidity sensor is suitable for humidity detection above 30% RH in both sealed and open environments.

A nanowire WO3 humidity sensor integrated with micro-heater and inverting amplifier circuit on chip manufactured using CMOS-MEMS technique

A Novel Serial High Frequency Surface Acoustic Wave Humidity Sensor

Single chip integration of MWCNTs/SiO2 thin film humidity sensor based on standard CMOS IC process

Design Of Single Chip Integration Of Mwnts/Sio2 Humidity Sensor And Its Interface Asic

QCM-based Humidity Sensor and Sensing Properties Employing Colloidal SnO2 Nanowires

ZnO nanowires grown on SOI CMOS substrate for ethanol sensing

Chip-Scale Humidity Sensor Based On A Silicon Nanobeam Cavity

Monolithic Integrated Cmos-Mems Mos Type Gas Sensor And Novel Heater For Sensitivity And Power Consumption Enhancement

Ultrafast Self-Assembly MoS2/Cu(OH)2 Nanowires for Highly Sensitive Gamut Humidity Detection with an Enhanced Self-Recovery Ability.

An Excellent Humidity Sensor Made of Surface Acoustic Wave Resonator Coated with MWCNTs/Nafion Composite Material Films

A Novel Humidity Sensor Based on Alumina Nanowire Films

Design of Conductive MWNTs/SiO<sub>2</sub> Humidity Sensor Interface ASIC Based on AC Signals

Design of conductive MWNTs/SiO2 humidity sensor interface ASIC based on AC signals

Design and Fabrication of MOS Type Gas Sensor with Vertically Integrated Heater Using CMOS-MEMS Technology

High-temperature humidity sensors based on WO3–SnO2 composite hollow nanospheres

Humidity sensing properties of a single Sb doped SnO2 nanowire field effect transistor

Copper-oxide Nanowires based Humidity Sensor

GO/CNT−OH/Nafion Nanocomposite Humidity Sensor Based on the LC Wireless Method

High-precision Silicon Nanowire Array Sensor for quantitating ambient humidity and pH value

From Ceramic Tube to Microcantilever: A New Strategy for Low Power, Fast Heating and High Integrated Metal Oxide Semiconductor Gas Sensor

Monolithically and Vertically Integrated Environmental Sensing Hub with Novel Air-Based Humidity Sensor Design