Abstract:The effects of the area reductions on the crystal orientation, eccentricity, and mechanical properties of GH4145 alloy tubes prepared by three-roller cold rolling were studied. Electron backscattered diffraction analysis showed that the equiaxed grains of the annealed tube blank gradually changed into elongated crystals along the axial direction (AD) with increased deformation. In addition, the grain orientations rotated from random distribution towards the <101>//radial direction (RD), <111>//AD, and <101> + <111>//tangential direction (TD). Brass, copper, S, and {123}< 111‾ > textures formed and increased in strength with increasing strain. Room-temperature tensile tests loaded along the AD and TD demonstrated yielding anisotropy of the tubes. With increasing strain, the work hardening increased continuously, and the dislocations slipped in three directions and then transformed into slip bands and dislocation cells, whereas a few deformation twins formed as the reduction reached 64%, and then slipped in two directions. When the reduction was 64%, the activated slip system transformed from {111}<110> to {110}<001> in most grains under applied AD loading, which was consistent with the loading in both directions at a reduction of 72%. As the grains in the preferential deformation zone near the inner and outer walls rotated to the <101>//RD orientation, the tubes plastically deformed, and the grains in the central layer then gradually begin to rotate. The ratio of radial length in the deformation hysteresis zone to wall thickness was used to represent the degree of non-uniformity of the deformation. A direct correlation was found between the eccentricity of the wall thickness and the non-uniformity of tube deformation as the area reduction increased from 13% to 50%. In addition, the radial delamination of the tubes disappeared, deformation became uniform, and the eccentricity decreased significantly as the area reduction increase up to 64%. Therefore, the dimensional accuracy and uniformity of the tubes can be further improved by controlling the strain of the tube.

Effect of Secondary Cold Reduction Rates on Microstructure, Texture and Earing Behavior of Double Reduction Tinplate

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Effect of Secondary Cold Rolling Reduction Rate on Secondary Recrystallization Behavior of CGO Steel

Effect of cold rolling reduction on microstructure, mechanical properties, and texture of deep drawing dual-phase (DP) steel

Effect of Reduction Ratio in Secondary Cold-rolling on Microstructure and Texture of V and Ti-contained Grain-oriented Silicon Steel

Effects of cold-pre-rolling reduction on precipitation of 2519A aluminum alloy plate

Influence Mechanisms of Cold Rolling Reduction Rate on Microstructure, Texture and Magnetic Properties of Non-Oriented Silicon Steel

Effect of Cold Rolling Reduction Ratio on Microstructure and Mechanical Properties of Fe–10Mn–4Al-0.4C Steel Containing Δ Ferrite

Effect Of Cold Rolling Before Hydrogen Reduction On Reduction Behavior And Morphologies Of Oxide Scale On Hot-Rolled Low-Carbon Steel

Effect of Rolling Reduction on Microstructures and Mechanical Properties of Sc-Containing Al-3.2Cu-1.5Li Alloy

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel

Effect of Cold Rolling Process on Microstructure, Texture and Formability of 00cr21monbti Ferritic Stainless Steel

Effects of Cold Rolling Reduction Rate on the Microstructure and Properties of Cu-1.16Ni-0.36Cr Alloy after Thermo-Mechanical Treatment

Effect of carbon content and microstructural refinement on the mechanical property of quenching-partitioning - tempering-treated steels

Effects of Reduction Partitioning in Two-Stage Cold Rolling on the Surface Ridging Resistance of Ferritic Stainless Steel

Effect of Cold Rolling Degree on Texture Evolution, Eccentricity, and Yielding Anisotropy of GH4145 Alloy Tubes

Effect of Rolling Reduction and Temperature on the Oxide Scale of Hot Rolled Mild Steel Strip

Influences of Trace Residual Elements Cr,Ni and Cu on Microstructures and Tensile Properties of SPHC Cold-Rolled Strip

Dislocation Strengthening and Texture Evolution of Non-Oriented Fe-3.3 wt% Si Steel in Double Cold Rolling

Microstructure, Texture, and Deep Drawability under Two Different Cold-Rolling Processes in Ferritic Stainless Steel

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling