Abstract:The major problem with quad flat no-lead package (QFN) packages is the delamination between the copper lead-frame and the molding compound (MC) due to relatively weak adhesion. The copper lead frame has excellent electrical and thermal conductivity. However, moisture penetration not only reduces the adhesion between the interfaces of the two materials, but also adversely affects the conductivity of Cu. Interface stratification is attributed to different material properties such as mismatch of coefficient of moisture expansion (CME), surface treatment of the mold pad, thermal strain, vapor pressure at high temperatures, and reduced interface strength due to moisture and temperature effects.The work presented in this paper focused on moisture, thermal and vapor pressure effects on the lead-frame and molding compound in the QFN during the precondition test and reflow process. The causes of delamination were examined both experimentally and via simulations. In an electronic package, the main failure effect stems from molding compound. To accurately simulate the moisture distribution in QFN, in this work, the moisture mechanism pertaining to material properties was investigated. This investigation focused on the MC and epoxy coefficient of moisture expansion and vapor pressure, and the parameters obtained by experimental study were incorporated into a simulation model to verify the fit between the experimental and the simulation findings. The electronic components employed in this work are standard for moisture sensitive testing, according to JEDEC J-STD-020D. To measure the specimen weight gain and geometric size, electronic balance and microscope were used, and these values were obtained under moisture sensitive level 1, level 2 and level 3 in order to establish the moisture desorption rate of the QFN package. And also according to the different degree of oxidation on the leadframe, the surface analysis of the material is carried out by environmental scanning electron microscope (ESEM) to understand the element distribution and interfacial strength. In addition, finite element analysis (FEA) was performed to analyze the stress, warpage and delamination in QFN packages. In this research will discuss the coupling forces of moisture, thermal stress and vapor pressure under MSL-3 and Reflow, and discuss the interface strength under different reliability test stages. To verify the accuracy of simulation modeling, the delamination site was observed and was aligned with the simulation results by applying scan acoustic tomography (SAT). Finally, the reliability of QFN was enhanced by investigating the moisture behavior of the materials co mprising the QFN.

Thermo-Hygro-Mechanical Design and Reliability Analysis for CMOS Image Sensor

Thermal stress of MOEMS Accelerometers Based on Grating Interferometric cavity

Hygrothermal Stress Analysis for a Micro-Camera Module under the Moisture Sensitivity Level One

Development and Reliability study of 3D WLCSP for automotive CMOS image sensor using TSV technology

Simulation and Analysis of Quad Flat No-lead Package (QFN) under Moisture, and Thermal Stress

Compensation for Process and Temperature Dependency in a CMOS Image Sensor

Reliability Evaluation of Interconnection in COM Package

Investigation on the effect of the packaging-induced stress on the reliability of a MEMS sensor package

Effects of Moisture Diffusion on a System-in-Package Module by Moisture–Thermal–Mechanical-Coupled Finite Element Modeling

Investigation of Stress in MEMS Sensor Device Due to Hygroscopic and Viscoelastic Behavior of Molding Compound

In-situ characterization of moisture absorption and hygroscopic swelling of silicone/phosphor composite film and epoxy mold compound in LED packaging

Investigation of Photosensitive Polyimide With Low Coefficient of Thermal Expansion and Excellent Adhesion Strength for Advanced Packaging Applications

Vertically Integrated Cmos-Mems Capacitive Humidity Sensor And A Resistive Temperature Detector For Environment Application

Development and Reliability Study of 3D WLCSP for CMOS Image Sensor Using Vertical TSVs with 3:1 Aspect Ratio

Design and Simulation of an Application Specific CMOS Image Sensor

Moisture Diffusion and Hygroscopic Swelling of Adhesives in Electronics Packaging

Finite element analysis of 2.5D packaging processes based on multi-physics field coupling for predicting the reliability of IC components

Determining the thermal expansion coefficient of thin films for a CMOS MEMS process using test cantilevers

Integration of infrared sensor and pressure/humidity/temperature cmos-mems environmental sensing hub by local vacuum packaging

Experiments and Hygrothermal Stress Analysis for a QFN Package.

Influences of hygrothermal conditions and structure parameters on moisture diffusion behavior in a system‐in‐package module by moisture-thermal-mechanical-coupled finite element modeling