Abstract:Cermets are ceramic–metal composites with a relatively high content of ceramic phases ranging from 15 to 85 vol %. It is shown that, if in the 20th century cermets have been considered mainly composites of high-temperature carbide, oxide, nitride, boride, and silicide-based ceramic phases with iron-group metallic phases, then in the 21st century the concept of cermets has significantly expanded owing to the appearance of composites made of ceramic and metal phases with lower melting points, including sulfides and MAX phases, as well as light and low-melting metals (Al, Mg, Cu, Ag, Pb, and Sn). In connection with this, cermets have begun to be considered not only as tooling and heat- and wear-resistant heavy structural materials, but also as light, strong structural materials for the production of vehicles and functional materials for different purposes. However, cermets are quite often characterized by disadvantages such as a tendency to brittle destruction, the difficulty of achieving uniformity and reproducibility of a structure, and the detection of defects therein, as well as the high production cost of such materials. All this makes it necessary to further development them; conduct studies on improving the composition, structure, and properties of cermets; search for new applications; develop novel methods for manufacturing cermets; and reduce production costs. Different methods for manufacturing cermets are discussed, including solid-phase, liquid-phase, gas-phase, and in situ methods. Methods of infiltration with metal melts, the effect of wetting, and the conditions for the implementation of spontaneous infiltration are considered in more detail. The results of the application of self-propagating high-temperature synthesis (SHS) are also described in detail, including a novel method for manufacturing cermets based on the use of the SHS of a porous ceramic framework followed by spontaneous infiltration with a molten metal proposed by the authors of this review.

TIC/Al cermet (ceramics+metal) structuring and composition forming with spontaneous infiltration of aluminum melt into a porous hot titanium carbide frame obtained by the SHS (Self-propagating high temperature synthesis) method

Structure and Phase Composition of SHS Products in Powder Mixtures of Titanium, Carbon, and Aluminum

Self-Propagating High-Temperature Synthesis in a Ti−Al−C Powder System Using Different Carbon Precursors

Preparation of Al–TiC Composites by Self-Propagating High-Temperature Synthesis

SHS Compaction of TiC-Based Cermets Using Mechanically Activated Mixtures

In Situ Synthesis of Al–TiC in Aluminum Melt

The Preparation of TiC/TiN Composites by Selective Laser Melting

Microstructure and formation mechanism of TiC-30Fe cermet fabricated by SHS

DENSE TiC-Al2O3-Fe CERMET FABRICATED BY SHS

Preparation of Ti/Al based nanophase composite powder by mechanical alloying

Nano- and Submicron-Sized TiB2 Particles in Al–TiB2 Composite Produced in Semi-Industrial Self-Propagating High-Temperature Synthesis Conditions

SYNTHESIS OF COMPOSITE POWDERS «TIC – NICRBSI ALLOY BINDER» FOR CLADDING AND DEPOSITION OF WEAR-RESISTANT COATINGS

In situ synthesis of TiC reinforced metal matrix composite (MMC) coating by self propagating high temperature synthesis (SHS)

Applying Infiltration Processes and Self-Propagating High-Temperature Synthesis for Manufacturing Cermets: А Review

Al3Ti/Al composites prepared by SHS

Fabrication of Ti2AlC ceramic bonded diamond composites by self-propagation high temperature sintering

Investigation of the Microstructure of Sintered Ti-Al-C Composite Powder Materials under High-Voltage Electrical Discharge

TiC-Fe cermets fabricated by SHS

Self-Propagating High-Temperature Synthesis of Layered Composite Ti/Hf/Ta/Ni/Ceramics Materials

Manipulating interface bonding and microstructure via tuning interfacial reaction for enhancing mechanical property of in-situ TiC/Al cermets

Production of B4C-TiB2 composite powder by self-propagating high-temperature synthesis