Abstract:Objective To study the incorporation rate and release behavior of bovine serum albumin(BSA) incorporated into the calcium phosphate coating by biomimetic deposition,as well as the physical and chemical properties of the hybrid coating,and to provide experimental basis for the fabrication of growth factor/biomimetic calcium phosphate coating and exploration for the loading/release behavior of growth factors.Methods Pure titanium specimens were immersed into saturated calcium phosphate solutions(SCP) containing no BSA(controlled group) and 3 different concentrations of BSA(experimental groups):1,10 and 100 mg/L.Biomimetic calcium phosphate coating was formed on titanium surface and BSA was incorporated into the coating through co-deposition.The topography of the specimen was observed using scanning electron microscopy(SEM).Chemical structure and phase composition of coatings were detected by Fourier infrared spectroscopy(FTIR) analysis and X-ray diffraction(XRD) respectively.BSA incorporation rate and release profile were determined by bicinchoninic acid protein assay kit.Results The biomimetic calcium phosphate coating was mainly composed of hydroxyapatite and octacalcium phosphate.BSA was successfully incorporated into the calcium phosphate coatings in all the 3 experimental groups.With the increase of BSA concentration,plate-like units of the coatings were turned into small grid structure.BSA incorporation rates of the three experimental groups were(72.4 ± 2.4)％,(62.3 ± 0.9)％ and (42.2 ± 1.7)％ respectively.The in vitro release test showed that all three BSA release profiles could be divided into two significant different stages:early burst release stage and later sustained release stage.The amount of BSA release of the 3 experimental groups in 24 h and 30 d were (1.57±0.09),(8.82±0.93),(140.24±3.12) μg,and (2.39±0.29),(14.39±0.70),(151.06±2.00) μg respectively.Conclusions Biomimetic calcium phosphate coating can be used as an effective carrier for protein.BSA concentration has an impact on the incorporation rate and release speed of BSA from the calcium phosphate coating.Favorable BSA incorporation rate and release behavior can be obtained at BSA concentration of 10 mg/L.

BSA/HA Coating on Titanium Alloy for Direct Bond Formation

[Experimental Study of Fast Formation of Biomimetic Apatite Coatings on Pure Titanium Surface].

Fabrication of bovine serum albumin/calcium phosphate bioactive coating on porous titanium scaffolds

Longer-Term Mechanical And Biological Evaluation Of Titanium Alloy Coated With Apatite Layer

Apatite Layer-Coated Titanium for Use As Bone Bonding Implants

[Fast Formation of Biomimetic Apatite Coatings on Pure Porous Titanium Implant's Surface].

Preparation and biological evaluation of Nano-HA coating on tatinium surfaces

Bone-like growth of hydroxyapatite in the biomimetic coating of Ti-6Al-4V alloy pretreated with protein at 25 °C

Osteoblast Response to Porous Titanium Surfaces Coated with Zinc-Substituted Hydroxyapatite

Study on the in vitro release behavior of bovine serum albumin from calcium phosphate coating on pure titanium surface

Biomimetic Calcium Phosphate Coatings for Bioactivation of Titanium Implant Surfaces: Methodological Approach and In Vitro Evaluation of Biocompatibility

Design and in Vitro Evaluation of Simvastatin-Hydroxyapatite Coatings by an Electrochemical Process on Titanium Surfaces

Osteoblast Responses to Thin Nanohydroxyapatite Coated on Roughened Titanium Surfaces Deposited by an Electrochemical Process.

Bioactive Composite Coating on Titanium Implants for Hard Tissue Repair

Preparation of Dicalcium Phosphate Anhydrous (Monetite) Biological Coating on Titanium by Spray-Drying Method

In Vitro Evaluation of Biologically Derived Hydroxyapatite Coatings Manufactured by High Velocity Suspension Spraying

Biomimetic Deposition of Hydroxyapatite by Mixed Acid Treatment of Titanium Surfaces

Development of Bioactive Ceramic Coating on Titanium Alloy substrate for Biomedical Application Using Dip Coating Method

Preparation of a hydroxyapatite/β calcium phosphate coating with high bonding strength on a titanium substrate

Preparation of Layered Bioceramic Hydroxyapatite/Sodium Titanate Coatings on Titanium Substrates Using A Hybrid Technique of Alkali-Heat Treatment and Electrochemical Deposition

Preparation of Hydroxyapatite Coating by Using Citric Acid Sodium Citrate Buffer System in the Biomimetic Procedure