Abstract:High-power impulse magnetron sputtering (HiPIMS), a new physical vapor deposition technique which combines the advantages of the high ionization rates of the sputtered materials and control of electromagnetism, has been widely used to deposit high-performance coatings with a large density and high adhesion. However, HiPIMS has some intrinsic disadvantages such as the low deposition rate, unstable discharge, and different ionization rates for different materials thereby hampering wider industrial adoption. We have recently designed an optimized cylindrical source based on the hollow cathode effect to circumvent the aforementioned limitations. However, during the operation of the cylindrical source, the discharge is inhomogeneous and the etching stripes are nonuniform. In order to determine the underlying mechanism and optimize the electromagnetic control, the discharge in the HiPIMS cylindrical source is simulated. The tangential magnetic field distribution on the target surface of the cylindrical sputtering source is inhomogeneous and electron runaway is serious, resulting in a relatively low plasma density. Two solutions are proposed to improve the situations. The first one is electrical improvement by installing an electron blocking plate, and the second one is magnetic improvement by adding compensating magnets. Our simulation results of the first method show that a potential well is produced by the electron blocking plate to suppress electron runaway and the plasma density is improved significantly, especially around the central cross-section of the cylindrical sputtering source. The discharge becomes homogeneous, and the etching stripes are uniform albeit not full enough. The second method of magnetic improvement significantly improves the homogeneity of the tangential magnetic field distribution on the target surface and the target utilization rate. After adding the optimized compensating magnets, the shape of the effective area (the value of the tangential magnetic field in a range of 25-50 mT) on the target surface can be controlled and made zonal. The target utilization rate increases to over 80% from 60%. In order to obtain the optimal conditions, the two techniques are combined. A larger and more homogeneous etching ring is observed by adopting both the electrical and magnetic improvements as predicted and explained by the simulation results. It can be concluded that the combination of the two improvement techniques can improve and optimize the HiPIMS cylindrical source.

Recouping etch rates in pulsed inductively coupled plasmas

Study of Synchronous RF Pulsing in Dual Frequency Capacitively Coupled Plasma

High energy electrons induced by nonlinear effect in synchronized dual-level radio frequency pulsing capacitively coupled plasmas

Effect of Embedded RF Pulsing for Selective Etching of SiO2 in the Dual-Frequency Capacitive Coupled Plasmas.

Across wafer etch rate uniformity in a high density plasma reactor: Experiment and modeling

Experimental Study of SiO2 Sputter Etching Process in 13.56 MHz Rf-Biased Inductively Coupled Plasma

Two-Dimensional Discharge Simulation of Inductively Coupled Plasma Etcher

Sub-damage-threshold plasma etching and profile tailoring of Si through laser-stimulated thermal desorption

REACTION SIMULATION AND EXPERIMENT OF A Cl2/Ar INDUCTIVELY COUPLED PLASMA FOR ETCHING OF SILICON

Pulse‐time‐modulated electron cyclotron resonance plasma etching for highly selective, highly anisotropic, and notch‐free polycrystalline silicon patterning

Electron dynamics and SiO2 etching profile evolution in capacitive Ar/CHF3 discharges driven by sawtooth-tailored voltage waveforms

Ion energy distribution functions in a dual-frequency low-pressure capacitively-coupled plasma: experiments and particle-in-cell simulation

Study on the Key Parameters in Etching of Fused Silica Using Atmospheric Inductively Coupled Plasma

ICP vs CCP in High Aspect Ratio Etching of SiO2 using Ar/C4F8/O2 Gas Mixtures

The Effect of Discharge Conditions of ICP Etching Reactor on Plasma Parameters

Electromagnetic Control and Optimization of High Power Impulse Magnetron Sputtering Discharges in Cylindrical Source

Voltage waveform tailoring for high aspect ratio plasma etching of SiO2 using Ar/CF4/O2 mixtures: Consequences of ion and electron distributions on etch profiles

Particle control via cryopumping and its impact on the edge plasma profiles of Alcator C-Mod

Hybrid simulation of radio frequency biased inductively coupled Ar/O 2 /Cl 2 plasmas

Recent developments in pulsed magnetron sputtering