Abstract:High-chromium martensitic steels are a promising material for the production of elements of boilers and steam pipelines, as well as blades and rotors of steam turbines for new coal-burning thermal generating units. The use of such materials will give an opportunity for the transition to ultra-supercritical steam parameters (temperature of 600–620 °C and pressure of 25–30 MPa), which will allow increasing the efficiency of generating units to 45 %. Modifications of the chemical composition of high-chromium steels have led to significant improvements of high-temperature properties such as 100,000 h creep strength and 1 % creep limit, while resistance to softening due to low-cycle fatigue remains understudied in this field. This work covers the study of low-cycle fatigue at room temperature with different amplitudes of deformation of martensitic high-chromium 10%Cr–3%Co–2%W–0.5%Mo–0.2%Cu–0.2%Re–0.003%N–0.01%B steel. The steel was pre-subjected to normalizing at 1050 °С followed by tempering at 770 °С. After heat treatment, the steel structure was a tempered martensitic lath structure stabilised by the particles of secondary phases of M23C6 carbides, NbX carbonitrides, and M6C carbides. The average width of martensite laths was 380 nm, and the dislocation density was 1.4×1014 m−2. At low-cycle fatigue, with an increase in the strain amplitude from 0.2 to 1 %, the number of cycles before failure significantly decreases, and the value of plastic deformation in the middle of the number of loading cycles significantly increases. Maximum softening (18 %) is observed at a strain amplitude of 1 % in the middle of the number of loading cycles. In general, the steel structure after low-cycle fatigue tests does not undergo significant changes: the width of the laths increases by 18 % at a strain amplitude of more than 0.3 %, while the dislocation density remains at a rather high level (about 1014 m−2) at all strain amplitudes.

Structural and Mechanical Characterization of Service Exposed 2.25Cr–1Mo Steel

Effect of on-site service for 16,000 and 38,000 h on microstructure and mechanical properties of austenitic steel HR3C reheater tubes

Microstructural Evolution and Oxidation Resistance of T92 Boiler Tube Steel Upon Long-Term Supercritical Steam Test

Microstructure-Property Relationship and Embrittlement Mechanism of HR3C Steel with High-Temperature Service of 65000 h

Low Cycle Fatigue and Creep Fatigue Interaction Behavior of 9Cr-0.5Mo-1.8w-v-nb Heat-Resistant Steel at High Temperature

Effect of high temperature service on the complex through-wall microstructure of centrifugally cast HP40 reformer tube

Revealing influence of warm bending on creep performance of heat-resistant 2.25Cr-1Mo-0.25 V steel

Microstructure and mechanical properties characterization of aged and repair welded Alloy 617M

Microstructural Evolution of a Re-Containing 10% Cr-3Co-3W Steel during Creep at Elevated Temperature

The Morphological and Compositional Changes of the Carbides in F12 Heat-Resistant Alloy Steel for Long-Term Service at Elevated Temperature

An Investigation of the Embrittlement in X20crmov12.1 Power Plant Steel after Long-Term Service Exposure at Elevated Temperature

High-Temperature Degradation and Protection of Ferritic and Austenitic Steels in Steam Generators

Study on performance degradation of main steam pipe of X20CrMoV12.1 steel for long-term service

D123 Damage Assessment of Highly Aged Thermal Power Boiler Tubes by TEM-Size SP Creep Test

Analysis of the Creep Mechanism of Low-Alloy Steel in Terms of Plastic Deformation

Creep Damage Assessment of Ex-Service 12% Cr Power Plant Steel Using Digital Image Correlation and Quantitative Microstructural Evaluation

Endurance Strength and Residual Life Assessment of T23 Steel after 96000 Hours of High Temperature and High Pressure Service

Oxidation Behaviors of Different Grades of Ferritic Heat Resistant Steels in High-Temperature Steam and Flue Gas Environments

Investigation of damage on FeCr26Ni36Co15W5 alloy reduction furnace tube during service

Low-cycle fatigue of 10 % Cr steel with high boron content at room temperature