Abstract:Micro-EDM is an unconventional technology used to machine every type of electrically conductive material regardless of its mechanical properties. Material removal occurs through electrical discharges between the workpiece and the electrode immersed in a dielectric fluid. In drilling operations, the technology is able to realise microholes with excellent quality in terms of precision, quality surface, roundness, and taper to the detriment of the machining time, which is less than other technologies. Several efforts are being made to improve different features related to the process performance that are severely affected by both the operative conditions, such as the electrode material or the type of dielectric, and process parameters. The typical indexes used to characterise the performance are the machining time, the material removal rate, and the geometric indexes. These indexes are very effective and are easily measurable, but they do not give information about the evolution of the drilling process, which could be irregular due to the different phenomena occurring during machining. The aim of this paper is the development of a method able to elaborate the motion law of the electrode during the micro-EDM drilling operation. In order to do this, a single hole was manufactured in several steps, recording both the machining time and electrode wear for each step. In this way, the actual position of the electrode during the drilling can be measured without the use of a predictive model for electrode wear. It was tested to confirm that the multistep procedure did not introduce new phenomena, in contrast to the traditional drilling operation. This method was used to study the effects of the electrode diameter, the type of electrode, the length of the electrode out of the spindle, and the entity of the run-out on the process performance. The tests were executed on titanium alloy sheets using a tungsten carbide electrode and hydrocarbon oil as the dielectric. It was found that the descent of the electrode into the workpiece was not regular, but it depended on the level of debris concentration in the machining zone. The debris concentration was influenced by the type and diameter of the electrode, its length out of the spindle, and, to a lesser extent, the run-out. This method was found to be a useful method for an in-depth analysis of the micro-EDM drilling process, contributing to a better understanding of the physical aspects of the process.

How the Electrical Conductivity of Water Fluids Affects Micro-EDM in the Short-Pulse Regime

Effect of Thickening Agent on Water-Based Working Fluid for EDM

Study of Alternating Current Flow in Micro-Edm Through Real-Time Pulse Counting

Study on the Electrical and Geometrical Parameters of Micro Electrical Discharge Machining

Experimental investigation of influence electrical discharge energy on the surface layer properties after EDM

Study of the Law Motion of the Micro-EDM Drilling Process

Effects of non-electrical parameters on the characteristics of discharge craters and machining performance in short electrical arc milling

Study on the influence that hard water had in high-speed wire electrical discharge machining

Material wear of the tool electrode and metal workpiece in electrochemical discharge machining

High-speed Near Dry Electrical Discharge Machining

Experimental Investigation and Optimization of Rough EDM of High-Thermal-Conductivity Tool Steel with a Thin-Walled Electrode

Theoretical and Experimental Investigation into Machining Characteristics of VHF Micro-EDM

Tailoring surface morphology and integrity of Inconel 718 using reciprocating Mo-wire and different discharge energy levels of WED-machining

Influence of Different Tool Electrode Materials on Electrochemical Discharge Machining Performances

Investigation on the Effect of Different Dielectric Fluids During Powder Mixed EDM of Alloy Steel

Comparative Study of Ultrasonic Vibration-Assisted Die-Sinking Micro-Electrical Discharge Machining on Polycrystalline Diamond and Titanium

Influence of Different Dielectrics and Machining Parameters for Electrical Discharge-Assisted Milling of Titanium Alloy

Improvement of ultrasonic cavitation and pumping effect in microhole EDM

Performance Analysis and Optimization of Different Electrode Materials and Dielectric Fluids on Machining of High Carbon High Chromium Steel in Electrical Discharge Machining

Influence of electrical parameters in electro discharge machining of tungsten heavy alloys on surface texture properties

Influence of Discharge Current on Machined Surfaces by Thermo-Analysis in Finish Cut of WEDM