Abstract:This study investigated the machinability of AISI H13 hot work tool steel with a hardness of 54 HRC, which has been deep cryogenically treated using the electro-erosion machining technique, one of the unconventional manufacturing methods. The machinability parameters used in the study were determined as current (4, 8 and 12 A), pulse time (200, 300 and 400 μs) and three different electrodes (Copper, Graphite and Tuncop). The experimental design was designed according to the Taguchi L 27 model, and machinability tests were carried out to examine the results obtained from the experimental study both experimentally and statistically. When the literature was examined, it was seen that cryogenic treatment was generally applied to electrode materials, and only surface roughness and material wear amounts were examined as output parameters. The original value of the study is the interpretation of the results by applying cryogenic treatment to the test material and exploring the surface roughness and material wear amount, as well as the hole diameters and criterion diameters formed on the treated surfaces after the EDM process. As a result of the study, it was observed that the surface roughness value, the hole diameter, the amount of material wear, and the crater diameter increased with the increase in ampere and impact time. The lowest surface roughness value was 2.266 μm in the graphite electrode material at 4 amps and 200 μs impact time and the highest wear amount was realized as 0.555 g in the copper electrode material 12 amps and 400 μs impact time. The smallest hole diameter was 12.254 mm with a tuncop electrode with a pulse duration of 4 amps and 200 μs, and the lowest crater diameter was 127.301 μm with a graphite electrode at a current of 4 amps and a pulse duration of 200 μs. When the signal-to-noise ratios were examined, the optimum machining parameters for surface roughness, hole diameter, material wear amount, and crater diameter were determined as A 2 B 1 C 1 , A 1 B 3 C 3 , A 3 B 1 C 1 , and A 3 B 1 C 1 , respectively. When the ANOVA results are examined, it is determined that the most effective parameter for the surface roughness is of the current value with 86.54%, the most effective parameter for the hole diameter is the electrode material with 85.20%, the most effective parameter for material wear amount is the electrode material with 45.67% and the most effective parameter for the crater diameter is current value with 75.35%.

Performance Analysis and Optimization of Different Electrode Materials and Dielectric Fluids on Machining of High Carbon High Chromium Steel in Electrical Discharge Machining

Optimization of EDM Machining of High Carbon High Chromium Steel Using Zirconium and Nickel Powder Mixed Dielectric by Grey Relational Analysis

Experimental Investigation and Optimization of Rough EDM of High-Thermal-Conductivity Tool Steel with a Thin-Walled Electrode

Performance capabilities of EDM of high carbon high chromium steel with copper and brass electrodes

Machining characteristics and optimization of process parameters in die-sinking EDM of Inconel 625

Investigation on the Effect of Different Dielectric Fluids During Powder Mixed EDM of Alloy Steel

Experimental Investigations On The Electrochemical Machining Of D3 Die Steel Material And Multi-Objective Parameter Optimization

Performance Analysis of Different Dielectric on Electrical Discharge Machined AA8011/SiC/Si3N4 Composites using Taguchi Coupled ELECTRE Approach

Influence of Different Tool Electrode Materials on Electrochemical Discharge Machining Performances

EDM Electrode Design and Analysis to Enhance Process Performance

Machinability Analysis and Optimization of Electrical Discharge Machining in AA6061-T6/15wt.% SiC Composite by the Multi-criteria Decision-Making Approach

Multi-objective Optimization of Electric Discharge Machining of Al-SiCp Composite by Taguchi-PCA, Firefly and Cuckoo Search Algorithm

Machinability of different cutting tool materials for electric discharge machining: A review and future prospects

Electric discharge machining performance measures and optimisation: a review

Experimental investigation and multi-objective optimization of eco-friendly near-dry electrical discharge machining of shape memory alloy using Cu/SiC/Gr composite electrode

Machining Of Inconel-825 Superalloy With Magnetic Field Assisted Electrical Discharge Turning: A Optimization Approach Using Response Surface Methodology And Multi-Objective Genetic Algorithm

Surface Characterization and Tribological Performance Analysis of Electric Discharge Machined Duplex Stainless Steel

Optimization of process parameters of powder mixed EDM for high carbon high chromium alloy steel (D2 steel) through GRA approach

Micro-Edm Of Ti–6Al–4V Using Various Tool Materials: Multi-Response Optimization And Surface Characterization

Optimizing micro-EDM with carbon-coated electrodes: A multi-criteria approach

Experimental and statistical investigation of electro-erosion machining performance of cryogenic treated hardened AISI H13 hot work tool steel