Abstract:The unsatisfactory high-temperature performance of commonly used silicon carbide (SiC)-based ceramics calls for a novel approach for their reinforcement. We present the in situ preparation of a SiC-based composite with uniformly dispersed titanium boride (TiB2) particles using titanium carbide and boron carbide as raw materials. Notably, the uniform incorporation of 25 wt%TiB2 results in the SiC–TiB2 composite with excellent tribological and self-lubricating properties at high temperatures. The SiC–TiB2 composite shows a friction coefficient of 0.20 and a specific wear rate of 5.77 × 108 mm3/(N mm), which are 4.75 times and ~ 5.2 times lower than that of the bare SiC ceramic at 1000 °C, respectively. The wear mechanism of a self-mated couple of the SiC–TiB2 composite is unraveled to be the tribo-oxidization. Since intimate contact exists between the oxidizing layer and the transitional layer of the fractured surface, the friction surface possessing plastic deformation properties may transit from brittle to plastic or elastic. The "Pin Effect" exhibited by TiB2 particles in the SiC–TiB2 composite deflects the crack propagation route. Meanwhile, a change in stress distribution, a decrease in the stress intensity of slight crack frontier, and an increase in "the threshold value" of crack propagation occur. The type (I + II) and type (I + III) complex cracks in fracture mechanics propagate non-flatly in the wearing process of the self-mated couple of the SiC–TiB2 composite. Besides, a fine yield deformation zone exists on the crack tip. Consequently, the "threshold value" of crack propagation fluctuates dynamically between "upper bound value" and "lower bound value" following the change in the valid length of actual crack propagation, thus delaying the fracture of the SiC–TiB2 composite.

Temperature-induced wear transition in ceramic-metal composites

Enhancing High-Temperature Wear Resistance by Constructing the Amorphous-Crystal Heterointerface Structure in WO3/TiO2 Composite Coatings

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

The Dry Sliding Wear Properties of Nano-Sized TiCp/Al-Cu Composites at Elevated Temperatures

Microstructure and Wear Behaviour of Ceramic Particles Strengthening Nial Based Composite

In situ preparation of a SiC–TiB2 composite and its wear fracture mechanism at high temperatures

Revealing the role of micron-sized in situ TiC particles on tensile properties and fracture mechanism of martensitic wear-resistant steel at elevated temperature

Tribological behaviors of vacuum hot-pressed ceramic composites with enhanced cyclic oxidation and corrosion resistance

Wear Behavior of Al 2 O 3 -Ticn Composite Ceramic Sliding on Stainless Steel

High-temperature oxidation and wear properties of TiC-reinforced CrMnFeCoNi high entropy alloy composite coatings produced by laser cladding

Properties and elevated temperature wear mechanism of pure copper and TiC/Cu nanocomposites

Wear transitions and tribochemical reactions in ceramics

High temperature fracture mechanism of ultrafine WC-Co cemented carbides containing (Ti,W)C

Dry wear characteristics of TC21 titanium alloy at elevated temperatures

On the reaction mechanism of Mo2FeB2-based cermets and wear transition induced by self-lubricating tribo-oxide layer

Mechanical and tribological performance of (TiNbTaWMo)C high-entropy ceramics in a wide temperature range

Establishing high temperature tribological performance and wear mechanism map of engineered in-situ TiB 2 reinforced Mg-RE metal matrix composites

Effect of quenched-tempered heat treatment on the wear resistance mechanism of zirconia toughened alumina ceramic reinforced high chromium cast iron architecture composite

High-performance TiN Reinforced Sialon Matrix Composites: A Good Combination of Excellent Toughness and Tribological Properties at a Wide Temperature Range

Wear Mechanism and Evolution of Tribofilm of Ceramic on Steel Pairs under Ester Oil Lubrication in Wide Temperature Range

Effect of Temperature on Wear Behavior in a Ti-V-Cr Base Fireproof Titanium Alloy