Abstract:Copper/graphite composites have received much attention in engineering applications due to their excellent thermal, electrical and self-lubricating properties. However, their mechanical and wear resistance properties are usually limited by the brittleness of graphite and the poor interfacial bond between graphite and copper. Harder particles can be used to reinforce composites to increase their mechanical properties and wear resistance. In this paper, copper/graphite composites added with Ti3AlC2 particles were prepared by rapid hot press sintering. Studies were conducted to find out how the sintering temperature affected the composites' phase composition, morphology, hardness, relative density, and friction properties. The results showed that the relative density and hardness of the composites increased and then decreased with increasing sintering temperature. Besides, the findings indicated that Al atoms started to diffuse out of Ti3AlC2 and into the Cu matrix around 800 °C, leading to the in-situ formation of TiCx and Cu(Al) alloys. When the sintering temperature exceeded 850 °C, Ti3AlC2 decomposed essentially completely. In comparison to other similar prior findings (the wear rate was ∼1 ×10−4 mm3·N−1·m−1), the copper/graphite composites prepared in this work shown improved wear resistance. Among them, the lowest wear rate (1.942 × 10−5 mm3·N−1·m−1) was obtained at a sintering temperature of 900 °C, with a relative density of 98.41%, a hardness of 75.67 HV and an average coefficient of friction of 0.15. This will help to further broaden the application areas of copper/graphite composites.

Properties and elevated temperature wear mechanism of pure copper and TiC/Cu nanocomposites

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Abrasive Wear and Physical Properties of In-Situ Nano-TiCx Reinforced Cu–Cr–Zr Composites

Enhanced mechanical and tribological properties of copper matrix composites reinforced by copper-coated graphite and Ti3AlC2

Effect of sintering temperature on microstructure and tribological properties of copper/graphite composites doped with Ti3AlC2 particles

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Dry sliding wear behavior of in situ Cu–TiB2 nanocomposites against medium carbon steel

Study on the Tribology Properties of the Particles/Cu Composite Coatings

Sliding Wear Behavior of TiB<sub>2</sub> Nanoparticle Reinforced Copper Matrix In-Situ Composites under Electric Current

Microstructure and properties of plasma sprayed copper-matrix composite coatings with Ti3SiC2 addition

The Dry Sliding Wear Properties of Nano-Sized TiCp/Al-Cu Composites at Elevated Temperatures

Microstructure and tribological behaviors of laser cladded CuAlMnTi–xTiC composite coatings at elevated temperature

Dry Sliding Friction and Wear Behavior of Cu-Nanosized TiB2 In-situ Composites

Investigation of the tribological mechanisms of TiN-ZrO 2 -B 4 C ternary ceramic-reinforced copper-metal matrix composites

Synthesis and Tribological Characterization of Ti3SiC2/ZnO Composites

Influence of Cu Content Variation on the Tribological Properties of Ni60CuMo with Sandwich-Structured Composite Coatings by Laser Cladding

Electrical sliding wear behavior of TiB2 nanoparticles reinforced copper matrix in-situ composite

Study of Friction and Wear Properties of Cu/Short Carbon Fibers Composites

Preparation and Characterization of In Situ (TiC-TiB2)/Al-Cu-Mg-Si Composites with High Strength and Wear Resistance

Wear behavior of self-propagating high-temperature synthesized Cu-TiO2 nanocomposites

Tuning composition and microstructure by doping Ti and C for enhancing mechanical property and wear resistance of Al0.2Co1.5CrFeNi1.5Ti0.5 high entropy alloy matrix composites