Abstract:The unsatisfactory high-temperature performance of commonly used silicon carbide (SiC)-based ceramics calls for a novel approach for their reinforcement. We present the in situ preparation of a SiC-based composite with uniformly dispersed titanium boride (TiB2) particles using titanium carbide and boron carbide as raw materials. Notably, the uniform incorporation of 25 wt%TiB2 results in the SiC–TiB2 composite with excellent tribological and self-lubricating properties at high temperatures. The SiC–TiB2 composite shows a friction coefficient of 0.20 and a specific wear rate of 5.77 × 108 mm3/(N mm), which are 4.75 times and ~ 5.2 times lower than that of the bare SiC ceramic at 1000 °C, respectively. The wear mechanism of a self-mated couple of the SiC–TiB2 composite is unraveled to be the tribo-oxidization. Since intimate contact exists between the oxidizing layer and the transitional layer of the fractured surface, the friction surface possessing plastic deformation properties may transit from brittle to plastic or elastic. The "Pin Effect" exhibited by TiB2 particles in the SiC–TiB2 composite deflects the crack propagation route. Meanwhile, a change in stress distribution, a decrease in the stress intensity of slight crack frontier, and an increase in "the threshold value" of crack propagation occur. The type (I + II) and type (I + III) complex cracks in fracture mechanics propagate non-flatly in the wearing process of the self-mated couple of the SiC–TiB2 composite. Besides, a fine yield deformation zone exists on the crack tip. Consequently, the "threshold value" of crack propagation fluctuates dynamically between "upper bound value" and "lower bound value" following the change in the valid length of actual crack propagation, thus delaying the fracture of the SiC–TiB2 composite.

Establishing high temperature tribological performance and wear mechanism map of engineered in-situ TiB 2 reinforced Mg-RE metal matrix composites

Microstructure and Wear-resistant Properties of in situ TiB-TiC Reinforced Titanium Matrix Composites by Laser Deposition Manufacturing

Abrasive Wear Behaviour of TiB2 Reinforced In-Situ Synthesized Magnesium RZ5 Alloy based Metal Matrix Composites

Development of wear maps of in-situ TiC+TiB2 reinforced AZ91 Mg matrix composite with varying microstructural conditions

Tribological behavior of in-situ nanosized TiB2 particles reinforced AZ91 matrix composite

Wear Performance of TiB2-Reinforced AZ91 Magnesium Metal Matrix Composite Fabricated by Ultrasonic Stir-Casting Process

Co-construction of microstructure evolution and wear resistance of in-situ TiBw/TA15 composites with network structure

Dry sliding wear behavior of XDTMZl201/TiB2 in-situ composite

Study of wear properties of in situ TiB/TiC reinforced Ti1100 composites

Dry Sliding Wear Characteristics of In-Situ TiBw/Ti6Al4V Composites with Different Network Parameters

DRY SLIDING WEAR BEHMIOR OF XD~(TM) ZL201/TiB_2 IN-SITU COMPOSITE

Investigation on Microstructures and Mechanical Behavior of In-Situ Synthesized TiC and TiB Reinforced Ti6Al4V Based Composite

Wear mechanism of XDTM ZL201–TiB2 in situ composite

Evaluation on tribological characteristics of (TiC+TiB)/Ti-6Al-4V composite in the range from 25 C to 600 C

Wear Behavior of Ti6Al4V Based Hybrid Composites Reinforced with TiB2(7.5%) + TiC (7.5%)

In situ preparation of a SiC–TiB2 composite and its wear fracture mechanism at high temperatures

Microstructure and Tribological Behavior of in Situ Synthesized (tib+tic)/ti6al4v (tib/tic=1/1) Composites

Preparation of in-situ ZrB2/A356 composites and high-temperature tribological studies

Effect of in situ TiC reinforcement and applied load on the high-stress abrasive wear behaviour of zinc–aluminum alloy

MORPHOLOGY OF WEAR DEBRIS DURING DRY SLIDING OF Ti6Al4V/TiC COMPOSITE AT ELEVATED TEMPERATURES IN VACUUM CONDITIONS

Wear Behavior of In-Situ TiC Particles Reinforced Aluminum Matrix Composite