Abstract:In order to investigate the effect of TiB2 contents on the microstructure and wear resistance of titanium matrix composites, commercial pure Ti (CP-Ti) powders with 0–7.5 wt.% TiB2 particles were melted by selective laser melting (SLM) to produce the in-situ Ti-TiB composites. When the TiB2 content increases from 2.5 wt.% to 7.5 wt.%, the microstructures of the Ti-TiB composites undergo a transition from the single phase of α′-Ti to the mixed phases of α′-Ti, TiB and TiB2, and the acicular α′-Ti is refined significantly from 1.03 ± 0.24 μm to 0.36 ± 0.05 μm, showing that increasing the TiB2 content induces the formation of TiB and refines the microstructure. Moreover, large TiB2 particles are not melted completely and they react with the Ti matrix liquid to form a TiB layer around the Ti matrix during SLM. However, small TiB2 particles are completely dissolved into the Ti matrix liquid so that the eutectic TiB grains are precipitated at the boundaries of the Ti matrix after in-situ reaction of TiB2 with Ti. The formation of α′ martensite in the titanium matrix and the addition of TiB2 can induce the fine grain strengthening, the dispersion strengthening, the solid solution strengthening in the SLM-produced composites. The results indicate that the microhardness of the composites increases from 258 ± 10.3 HV0.2 to 435 ± 14.7 HV0.2. The wear process of the SLM-produced CP-Ti and TiB2 reinforced Ti matrix composites is accompanied by adhesion wear, abrasive wear and oxidation wear. As a result, when the TiB2 content increases to 7.5%, the wear resistance of the composites increases by 32.6% compared with that of the CP-Ti. These improvements are mainly due to strengthening and hardening effects induced by TiB2 particles and refinement of Ti matrix. This study provides some basis for developing wear-resistant and high-strength titanium alloys.

Investigation on mechanical and tribological behaviour of titanium diboride reinforced martensitic stainless steel

Microstructure and Wear-resistant Properties of in situ TiB-TiC Reinforced Titanium Matrix Composites by Laser Deposition Manufacturing

Investigation of Mechanical and Tribological Properties of Al6061–TiB2 Metal Matrix Composites

Effect of TiB_2 content on microstructure and mechanical properties of in-situ fabricated TiB_2/B_4C composites

Influence of TiC Particles on Mechanical and Tribological Characteristics of Advanced Aluminium Matrix Composites Fabricated through Ultrasonic-Assisted Stir Casting

Effect of TiB2 content on microstructure and properties of in situ Ti-TiB composites

Optimization of Tribological Behaviour of Ti6Al4V/TiB2/TiC Hybrid MMCs Using Response Surface Methodology

Wear Behavior of Ti6Al4V Based Hybrid Composites Reinforced with TiB2(7.5%) + TiC (7.5%)

Mechanical and wear analysis of AA6061-T6-SiC-TiC-graphite metal matrix composite

Experimental Investigation on Tribological Performance of TiB2-CoTi Composite Coating Fabricated on AISI 304 Stainless Steel by Argon Arc Cladding Technique

Wear Performance of TiB2-Reinforced AZ91 Magnesium Metal Matrix Composite Fabricated by Ultrasonic Stir-Casting Process

Mechanical Properties of Titanium Diboride Particles Reinforced Aluminum Alloy Matrix Composites: A Comprehensive Review

Investigation on the effect of SiC and TiB2 ceramic particles on mechanical and tribological properties of Al7075 hybrid metal matrix composites prepared through conventional stir casting technique

Tribological, mechanical and microstructure characteristics of hybrid aluminium matrix composite containing titanium carbide (TiC) and graphite particles

Effect of Titanium Dioxide Particles on the Morphology, Mechanical, and Wear Properties of the Aluminum Alloy 3003-Based Composites

Investigation of Microstructural, Mechanical and Corrosion Properties of AA7010-TiB2 in-situ Metal Matrix Composite

Tribological behavior of in-situ nanosized TiB2 particles reinforced AZ91 matrix composite

Refined microstructure and enhanced wear resistance of titanium matrix composites produced by selective laser melting

Influence of In Situ Titanium Diboride Particulate Reinforcement on Mechanical Properties of Aluminum–Silicon Based Metal Matrix Composites

The Effect of Micron-Sized TiB2 Particles on the Properties of Al6061 Strengthened with 4% TiB2 Nano-TiB2

A study of processing and parametric optimization of wear-resistant AZ91-TiB2 composite fabricated by ultrasonic-assisted stir casting process