Abstract:Coupled chemical and mechanical phenomena at electrode interfaces largely govern the reversibility and long term stability of lithium ion and lithium metal batteries. A well-known example in lithium ion batteries is the formation of the electrically insulating, ionically conductive, continuous solid electrolyte interface (SEI) on graphitic anodes, which passivates the electrode against further electrochemical reduction of the electrolyte. Unfortunately, this stable passivation does not occur in Si and Li metal anodes. High voltage cathodes are also prone to detrimental interfacial processes, resulting in electrolyte oxidation, gas formation, and transition metal dissolution. In response, a myriad of coating technologies has been developed to mitigate and control these interfacial phenomena and enable next-generation electrodes. These technologies must provide thin, conformal coatings over the entire electrochemically active surface area of the electrode; the coatings must also possess the requisite mechanical properties to accommodate volume dilation due to lithium insertion/extraction. This presentation will describe the development of conformal, compliant polymer thin film coatings for lithium battery electrodes. The polymer thin films are prepared by initiated chemical vapor deposition (iCVD), which provides exquisite control over film composition and morphology by facilitating heterogeneous free-radical polymerization of vinyl monomers with thickness precision on the order of 1 nm. Poly(1,3,5,7-tetravinyl-1,3,5,7-tetramethylcyclotetrasiloxane) (pV4D4) was deposited onto silicon thin film electrodes using iCVD. 25 nm-thick pV4D4 films on Si electrodes improved initial coulombic efficiency by 12.9% and capacity retention over 100 cycles by 64.9% relative to untreated electrodes. PV4D4 coatings also improved rate capabilities, enabling higher lithiation capacity at all current densities. Post-cycling FTIR and XPS showed that pV4D4 inhibited electrolyte reduction and altered the SEI composition, with enrichment in LiF. In another example, thin conformal coatings of perfluorinated polymer were deposited onto battery-grade Cu current collectors to function as an artificial solid electrolyte interface. The effect of the film thickness on Li cycling reversibility was characterized. By galvanostatically cycling Li in an asymmetric Li||Cu cell using 1M LiFSI in a 1:1 (v/v) mixture of dioxolane:dimethoxyethane at 30°C, it was shown that the average coulombic efficiency averaged over 50 cycles increased from 98.36% for bare, untreated Cu to 99.08% for Cu coated with 25 nm of the fluoropolymer. Moreover, the 25 nm coating suppressed interfacial impedance growth on the current collector; the resistance of the coated Cu was 40% lower than the untreated Cu after 100 cycles. The mechanism by which the polymer coating enhances coulombic efficiency and suppresses side reactions will be discussed, along with discussion of the performance in practical anode-free lithium metal batteries.

Amorphous silicon coatings for control of corrosion and metal ion contamination

Fundamental nanoscale surface strategies for robustly controlling heterogeneous nucleation of calcium carbonate

Recent Frontiers in Anisotropic Wet Chemical Etching Techniques for Precision Surface Modification of Industrial-Grade Bulk Crystalline Silicon Wafers: Enhancing Performance in Photovoltaics and MEMS Devices

Toward Controllable Wet Etching of Monocrystalline Silicon: Roles of Mechanically Driven Defects

Amorphous SiC Thin Films Deposited by Plasma-Enhanced Chemical Vapor Deposition for Passivation in Biomedical Devices

Corrosion protection performance of silicon-based coatings on carbon steel in NaCl solution: a theoretical and experimental assessment of the effect of plasma-enhanced chemical vapor deposition pretreatment

Corrosion of stainless steels and corrosion protection strategies in the semiconductor manufacturing industry: a review

Improved Corrosion Protection of Aluminum Alloys by Electrodeposited Silanes

Toughening thin-film structures with ceramic-like amorphous silicon carbide films.

Metallization introduced corrosion and parylene protection of surface micromachined polysilicon film with submicron capacitive gap

Facile Preparation of Robust Superamphiphobic Surface by Electrochemical Etching Process Based on the SiC/Al Composites

An Amorphous Si-O-N Coating on Magnesium to Retard Corrosion & Improve Biocompatibility

Sol–Gel Silica Coatings for Corrosion Protection of Aluminum Parts Manufactured by Selective Laser Melting (SLM) Technology

Atomically controlled CVD processing of group IV semiconductors for ultra-large-scale integrations

Contamination Control in Semiconductor Manufacturing Processes

Large-Area Preparation of a Robust Superamphiphobic Coating for Chemical Mechanical Polishing Application

(Invited) Lithium Battery Interfacial Engineering with Thin Conformal Polymer Coatings

Thin, Transferred Layers of Silicon Dioxide and Silicon Nitride As Water and Ion Barriers for Implantable Flexible Electronic Systems

Conformal coating of amorphous silicon and germanium by high pressure chemical vapor deposition for photovoltaic fabrics

Investigating the Corrosion Resistance of Different SiC Crystal Types: From Energy Sectors to Advanced Applications