Abstract:This study presents the results of the evaluation of the purity of medical oxygen obtained by adsorption technology with pressure fluctuations, taking into account the variability of the parameters of the incoming air, and the results of the correlation analysis of data obtained from the monographs of the European and American Pharmacopoeias. The quality of oxygen obtained from air that meets sanitary standards and under conditions of the “worst case,” while fixing the time of the output of the slip signal of monoxide and carbon dioxide as marker gases, was assessed. The slip time under the experimental conditions was 13 h 22 min. The composition of the gas produced by installation was analyzed. Impurities of nitrogen, argon, and water were recognized as predominant quantitatively. Nitrous gases and sulfur dioxide were not detected. A comparative assessment of the data on medical oxygen (93%) presented in the European EP 8. 0 (No. 2455) and the American USP 38-NF (No. 4180) pharmacopeias showed that no single approach is available to assess the quality of 93% medical oxygen in pharmaceutical practice worldwide. The authors of the above-mentioned pharmacopeias note that installations for obtaining 93% medical oxygen, implementing adsorption technology with pressure fluctuations, must be equipped with gas-analytical devices to quantify the level of at least two impurities: carbon monoxide and dioxide. In general, the data obtained indicate that when obtaining 93% medical oxygen by adsorption technology with pressure fluctuations from air corresponding to sanitary and hygienic indicators (clean), the resulting gas did not contain impurities requiring quantitative assessment and/or identification. If oxygen in its pure form is rarely supplied to the patient, its further dilution to 40%–60% is more often required, and the content of hypothetically possible impurities becomes negligible. However, the technology of air separation on molecular sieves is a complex physicochemical (thermodynamic) process, and its effectiveness depends on the component composition of the incoming air, which may change when working under unfavorable environmental conditions in various locations. In this regard, medical oxygen production plants that implement this technology must employ gas-analytical devices to quantify the level of carbon dioxide and carbon monoxide impurities without fail.

Evaluation of oxygen separation from air by pressure/vacuum swing adsorption

The Production of Industrial-Grade Oxygen from Air by Pressure Swing Adsorption

Modelling and Simulation of Two-Bed PSA Process for Separating H2 from Methane Steam Reforming

Plateau-Adapted Single-Pump, Single-Bed Vacuum Pressure Swing Adsorption Oxygen Generation Process Simulation and Optimization

Experimental study on oxygen concentrator with wide product flow rate range: individual parametric effect and process improvement strategy

Multiscale design of a pressure swing adsorption process for natural gas purification

Experimental evaluation of the purity of medical oxygen obtained by adsorption technology with pressure fluctuations taking into account the variability of the parameters of the incoming air

Thermodynamic Exploration of Two-Stage Vacuum-Pressure Swing Adsorption for Carbon Dioxide Capture

Problems of analysis, optimization and control in the separation of gas mixtures

Review of the Pressure Swing Adsorption Process for the Production of Biofuels and Medical Oxygen: Separation and Purification Technology

Correlations Between Adsorbent Characteristics and the Performance of Pressure Swing Adsorption Separation Process

Pressure Swing Adsorption for Biogas Upgrading with Carbon Molecular Sieve

Separation of Methane and Nitrogen Using Heavy Reflux Pressure Swing Adsorption: Experiments and Modeling

Optimization of a Six-Step Pressure Swing Adsorption Process for Biogas Separation on a Commercial Scale

Modeling and optimal design of multicomponent vacuum pressure swing adsorber for simultaneous separation of carbon dioxide and hydrogen from industrial waste gas

Simulation and Energy Consumption Comparison of Gas Purification System Based on Elevated Temperature Pressure Swing Adsorption in Ammonia Synthetic System

Advances in Pressure Swing Adsorption for Gas Separation

Methane/nitrogen separation through pressure swing adsorption process from nitrogen-rich streams

To the problem of forming the equation system for pressure swing adsorption mathematical model

New hybrid membrane vacuum swing adsorption process for CO2 removal from N2/CO2 mixture: modeling and optimization by genetic algorithm

Green Hydrogen Recovery from Natural Gas Grids by Vacuum Pressure Swing Adsorption