Abstract:The constraints of traditional manufacturing techniques have led to the generation of a considerable amount of waste superalloy, causing substantial resource wastage. The primary concern with waste superalloys lies in the excessive presence of inclusions and impurity elements, rendering them unsuitable for further utilization. This study proposes the use of directional solidification combined with electron beam melting and refining (EBMR) to prepare FGH4096 superalloy ingots (Φ120 mm), which offers a promising approach to produce large-sized powder superalloy master alloy ingots with high-purity and high homogeneity. It is found that the secondary dendrite arm spacing and the size of the γ' phase in the alloy are significantly reduced after EBMR treatment. The concentration of O and N can be decreased to 5.7 and 0.6 ppmw, respectively. The size of inclusion can be reduced below 8.69 μm and the inclusion numbers reduce by over 50 % compared with both conventional ingots. A droplet transfer mode and melt convection mode mechanism have been proposed, which accurately predicts the melting temperature and melt flow. A quantitative study is conducted on the influence of inclusion density, the contact angle between inclusions and melt, and the surface tension of the melt on capillary forces. The results indicate that the capillary forces between inclusions in the melt range from 1.8 × 10 −19 N and 1.9 × 10 −17 N. Furthermore, the collision-aggregation behavior of inclusions in the melt is discussed, and an estimate of the tendency of inclusion collision-aggregation is provided. The enrichment of inclusions in the EBMR ingot is primarily the result of turbulent collision. The Marangoni effect and the extremely high surface temperature of the melt promote the collision and agglomeration of inclusions, causing them to accumulate rapidly at the melt surface. Moreover, the thorough removal of inclusions through the decomposition and dissolution process of the electron beam offers theoretical backing for the preparation of superalloys through electron beam melting and high-purity refining.

Technical research on recycling waste blades of single crystal superalloy through ultrasonic alkali cleaning combined with electron beam smelting

Research on directional solidification combined with electron beam melting and refining for recycling of FGH4096 alloy scraps

Mechanisms for removing impurities in a single crystal superalloy by electron beam drip melting

Compound purification of nickel base superalloy cutting waste through special cleaning agent attached to ultrasonic stirring

Recovery of Ti-bearing blast furnace slag and diamond wire saw silicon powder waste by alloying and electromagnetic separation technique

Leaching mechanism of strategic metals from superalloy scrap under ultrasonic cavitation

On the control of epitaxial growth and stray grains during laser-directed energy deposited Ni-based single crystal superalloy

Effect of electron beam melt superheating treatment on DZ125 alloy

An approach for simultaneous treatments of diamond wire saw silicon kerf and Ti-bearing blast furnace slag

Effects of processing parameters on the surface quality of wrought Ni-based superalloy by ultrasonic-assisted electrochemical grinding

Microstructural Evolution and Compositional Homogenization of a Low Re-bearing Ni-based Single Crystal Superalloy During Through Progression of Heat Treatment

A Review of Methodology Development for Controlling Loss of Alloying Elements During the Electroslag Remelting Process

Recycling of Ti and Si from Ti-bearing blast furnace slag and diamond wire saw silicon waste by flux alloying technique

Rafting-Enabled Recovery Avoids Recrystallization in 3D-Printing-Repaired Single-Crystal Superalloys

Experimental Investigation on Plastic Strain and Recrystallization of Single Crystal Nickel Based Superalloys

The Effect of Elemental Vaporization and Redistribution During Sub-Solvus Recrystallization of A Single Crystal Superalloy

Phase Field Simulation of Alloying Element Segregation During Solidification of DD5 Nickel-Base Single Crystal Superalloy

Custom-designed heat treatment simultaneously resolves multiple challenges facing 3D-printed single-crystal superalloys

Upgrading recycling of Al–7 wt%Si alloys using electromagnetic force in directional solidification

Effect of Thermal Stability of Γ′ Phase on the Recrystallization Behaviors of Ni-based Single Crystal Superalloys

A new process for efficient purification of 6061 aluminum alloy scrap under semi-solid and super-gravity conditions