Abstract:The highly reactive chemical nature of aluminum makes it production energy-intensive or essentially impossible to extract alloying elements from Al-based liquids. Using molten salt fluxing and electrolysis processes can effectively refine coarse Al scraps. However, the generation of toxic gases and hazardous dross during these processes can cause significant environmental protection challenges and result in notable social concerns. Therefore, the primary recycling of post-consumer Al in industries currently proceeds mainly in a cascade manner, which is not sustainable when considering the Al cycle trends in the coming decades. Herein, we develop a novel process to separate primary Al from the crystallizing liquid when a constant electromagnetic force (EMF) is applied. Using this technique, we successfully upgraded Al–7mass%Si (hereafter, unless specified otherwise) alloy to approximately Al–3.6%Si in directional solidification. The separation mechanism was discussed in terms of the electrical properties of the respective phases during solidification. Fluid flow simulation results were applied to elucidate the separation behavior in the alloy. The upper and lower limits to separate the crystallizing alloy into an Al-rich and Si-rich areas were determined when the controlling factors were clarified, which made it possible to scale up the present laboratory-based setup to an industrial level. Moreover, the energy consumption of the process was slightly higher than that required for remelting only. Using the EMF technique to separate the crystallizing alloy into Al-rich and Si-rich regions did not produce hazardous dross or toxic gases. This energy-saving and eco-friendly process can provide a breakthrough to overcome the "dead metal" crisis and thus realize sustainability by upgrading recycling of post-consumer hypoeutectic Al–Si casting alloys.

Recycling of Ti and Si from Ti-bearing blast furnace slag and diamond wire saw silicon waste by flux alloying technique

Recovery of Ti-bearing blast furnace slag and diamond wire saw silicon powder waste by alloying and electromagnetic separation technique

Effect of Al and MgO on the simultaneous alloying of diamond wire saw silicon waste and Ti-bearing blast furnace slag

Simultaneous recycling of Si and Ti from diamond wire saw silicon powder and Ti-bearing blast furnace slag via reduction smelting: An investigation of the effects of refractories on recycling

An approach for simultaneous treatments of diamond wire saw silicon kerf and Ti-bearing blast furnace slag

An approach to employ titanium-bearing blast-furnace slag to prepare Ti and Al–Si alloys

Preparation of high-purity TiSi2 and eutectic Si–Ti alloy by separation of Si–Ti alloy for clean utilization of Ti-bearing blast furnace slag

An Approach to Prepare Novel Tisi2 Alloy for Clean Utilization of Spent V2o5-Wo3/Tio2 Catalysts and Diamond-Wire Silicon Slitting Powder

Novel application of high temperature solution growth method in simultaneously preparing SiC/Ti 3 SiC 2 /TiC using photovoltaic Si waste and Ti-bearing blast furnace slag

A novel approach to prepare high-purity Si and Si/TiSi2 materials simultaneously using Ti-bearing blast furnace slag

High-value Recycling of Photovoltaic Silicon Waste: Accelerated Removal of Impurity Boron Through Na3AlF6-enhanced Slag Refining

Application of Pressure-less Sintering and Dynamic-Slag Treatment to Recover Diamond Wire Saw Silicon Powder

Recovery and Purification of Metallic Silicon from Waste Silicon Slag in Electromagnetic Induction Furnace by Slag Refining Method

Recycling of silicon from waste PV diamond wire sawing silicon powders: A strategy of Na2CO3-assisted pressure-less sintering and acid leaching

Separation and comprehensive utilization of valuable elements in Ti-bearing electric arc furnace molten slag

Separating and Recycling of Elemental Silicon from Wasted Industrial Silicon Slag

Upgrading recycling of Al–7 wt%Si alloys using electromagnetic force in directional solidification

Experiments on the Melting Properties of CaO-Al2O3-SiO2-TiO2 Slag

Separation and purification of silicon from cutting kerf-loss slurry waste by electromagnetic and slag treatment technology

Recovery of titanium, aluminum, magnesium and separating silicon from titanium-bearing blast furnace slag by sulfuric acid curing—leaching

A novel strategy for recovery of heavy metals and synthesis of Co-rich alloy from the alkali-treated tungsten residue using photovoltaic silicon kerf waste