Abstract:After the converter steelmaking process, a considerable number of ferroalloys are needed to remove dissolved oxygen from the molten steel, but it also forms a lot of oxide inclusions that cannot be completely removed. At the same time, it increases the carbon emissions in the steel production process. After years of research, our team have developed a series of clean deoxidation technologies, including carbon deoxidation, hydrogen deoxidation, and waste plastic deoxidation of molten steel to address the aforementioned issues. In this study, thermodynamic calculations and laboratory experiments were employed to verify that carbon and hydrogen can reduce the total oxygen content in the molten steel melt to below 5 × 10 −6 and 10 × 10 −6 , respectively. An analysis of the deoxidation mechanisms and effects of polyethylene and polypropylene was also conducted. In addition, the applications of carbon deoxidation technology in different steels with the hot-state experiment and industrial production were discussed carefully. The carbon deoxidation experimental results of different steels were as follows: (1) the oxygen content of bearing steel was effectively controlled at 6.3 × 10 −6 and the inclusion number density was lowered by 74.73% compared to aluminum deoxidized bearing steel; (2) the oxygen content in gear steel was reduced to 7.7 × 10 −6 and a 54.49% reduction of inclusion number density was achieved with almost no inclusions larger than 5 μm from the average level of industry gear steels; (3) a total oxygen content of M2 high-speed steel was as low as 3.7 × 10 −6 . In industrial production practice, carbon deoxidation technique was applied in the final deoxidation stage for non-aluminum deoxidized bearing steel, and it yielded excellent results that the oxygen content was reduced to below 8 × 10 −6 and the oxide inclusions in the steel mainly consist of silicates, along with small amounts of spinel and calcium aluminate.

Purification of Steel Mill Gases under Changing Feed Stock Conditions

Concentration Fluctuations in Steel Mill Gases: Analytics as Key to Develop Steel Off‐Gas Purification

Chemical Processes in Tar Removal from Biomass Derived Fuel Gas by Pulsed Corona Discharges

Reconfiguration of Acid Gas Removal Process Matching the Integration of Coal Chemical Industry with Green Hydrogen

Economic and Carbon Emission Analysis of Two Typical Denitrification Systems for Sintering Process in the Iron and Steel Industry

Usage of Converter Gas as a Substitute Fuel for a Tunnel Furnace in Steelworks

Carbon Cycle in A Steelmaking Mill: Recycling of Kish Graphite and Its Subsequent Application for Steelmaking Carburant

Study on the Catalytic Effect of Converter Dust on In Situ Online Reforming of Metallurgical By‐Product Gas and Thermochemical Energy Storage Analysis

Substitution of coke with pelletized biocarbon in the European and Chinese steel industries: An LCA analysis

Numerical investigation of the impact of injecting coke oven gas on raceway evolution in an ironmaking blast furnace

Coke and Blast Furnace Gases: Ecological and Economic Benefits of Use in Heating Furnaces

Development of Carbon Capture Absorbents for Top Gas Recycling-Oxygen Blast Furnace in the Steel Industry

Coal Tar Pitch Processing: Experimental and Theoretical Characteristics of Thermal Plasma Process Using DC Plasma Torch

Preparation and Application of Slag‐Based Catalyst for Steelmaking

Effect of furnace atmosphere on sintering process of chromium-containing steel via powder metallurgy

A Carbon Capture and Utilization Process for the Production of Solid Carbon Materials from Atmospheric CO2 – Part 1: Process Performance

A Numerical Study of Scenarios for the Substitution of Pulverized Coal Injection by Blast Furnace Gas Enriched by Hydrogen and Oxygen Aiming at a Reduction in CO2 Emissions in the Blast Furnace Process

Study on the reduction of Fe2O3 pellets by CO-CO2 and H2-H2O: Reaction kinetics and pore network model

Enriching blast furnace gas by removing carbon dioxide

New steelmaking process based on clean deoxidation technology

Electrified CO2 valorization in emerging nanotechnologies: A technical analysis of gas feedstock purity and nanomaterials in electrocatalytic and bio-electrocatalytic CO2 conversion