Abstract:Gasifier-derived syngas from coal has many applications in the area of catalytic transformation to fuels and chemicals. Raw syngas must be treated to remove a number of impurities that would otherwise poison the synthesis catalysts. Inorganic impurities include alkali salts, chloride, sulfur compounds, heavy metals, ammonia, and various P, As, Sb, and Se- containing compounds. Systems comprising multiple sorbent and catalytic beds have been developed for the removal of impurities from gasified coal using a warm cleanup approach. This approach has the potential to be more economic than the currently available acid gas removal (AGR) approaches and improves upon currently available processes that do not provide the level of impurity removal that is required for catalytic synthesis application. Gasification also lends itself much more readily to the capture of CO2, important in the regulation and control of greenhouse gas emissions. CO2 capture material was developed and in this study was demonstrated to assist in methane production from the purified syngas. Simultaneous CO2 sorption enhances the CO methanation reaction through relaxation of thermodynamic constraint, thus providing economic benefit rather than simply consisting of an add-on cost for carbon capture and release. Molten and pre-molten LiNaKCO3 can promote MgO and MgO-based double salts to capture CO2 with high cycling capacity. A stable cycling CO2 capacity up to 13 mmol/g was demonstrated. This capture material was specifically developed in this study to operate in the same temperature range and therefore integrate effectively with warm gas cleanup and methane synthesis. By combining syngas methanation, water-gas-shift, and CO2 sorption in a single reactor, single pass yield to methane of 99% was demonstrated at 10 bar and 330°C when using a 20 wt% Ni/MgAl2O4 catalyst and a molten-phase promoted MgO-based sorbent. Under model feed conditions both the sorbent and catalyst exhibited favorable stability after multiple test cycles. The cleanup for warm gas cleanup of inorganics was broken down into three major steps: chloride removal, sulfur removal, and the removal for a multitude of trace metal contaminants. Na2CO3 was found to optimally remove chlorides at an operating temperature of 450ºC. For sulfur removal two regenerable ZnO beds are used for bulk H2S removal at 450ºC (<5 ppm S) and a non-regenerable ZnO bed for H2S polishing at 300ºC (<40 ppb S). It was also found that sulfur from COS could be adsorbed (to levels below our detection limit of 40 ppb) in the presence of water that leads to no detectable slip of H2S. Finally, a sorbent material comprising of Cu and Ni was found to be effective in removing trace metal impurities such as AsH3 and PH3 when operating at 300ºC. Proof-of-concept of the integrated cleanup process was demonstrated with gasifier-generated syngas produced at the Western Research Institute using Wyoming Decker Coal. When operating with a ~1 SLPM feed, multiple inorganic contaminant removal sorbents and a tar-reforming bed was able to remove the vast majority of contaminants from the raw syngas. A tar-reforming catalyst was employed due to the production of tars generated from the gasifier used in this particular study. It is envisioned that in a real application a commercial scale gasifier operating at a higher temperature would produce lesser amount of tar. Continuous operation of a poison-sensitive copper-based WGS catalyst located downstream from the cleanup steps resulted in successful demonstration.

Reconfiguration of Acid Gas Removal Process Matching the Integration of Coal Chemical Industry with Green Hydrogen

Hydrogen Sulfide Removal Process Embedded Optimization of Hydrogen Network

High Yield of CO and Synchronous S Recovery from the Conversion of CO2 and H2S in Natural Gas Based on a Novel Electrochemical Reactor

Combined Energy Consumption And Co2 Capture Management: Improved Acid Gas Removal Process Integrated With Co2 Liquefaction

High Yield of CO and Synchronous S Recovery from the Conversion of CO 2 and H 2 S in Natural Gas Based on a Novel Electrochemical Reactor

Multi-technique integration separation frameworks after steam reforming for coal-based hydrogen generation

Advanced Rectisol wash equipment incorporating syngas liquefaction and methane recovery for enhanced energy management

Sulfide removal in coal liquefaction wastewater by gas stripping

Conceptual Design and Retrofitting of the Coal-Gasification Wastewater Treatment Process

Direct conversion of acid gases into H2: A systematic review

Optimized Process Configuration for CO2 Recovery from Crude Synthesis Gas Via a Rectisol Wash Process

New Solvents for CO2 and H2S Removal from Gaseous Streams

Selective Removal of H2S over CO2 in a Membrane Gas–liquid Microdisperison Microreactor

Highly-efficient natural gas desulfurization and simultaneous H2O2 synthesis based on the electrochemical coupling reaction strategy

Coal-Derived Warm Syngas Purification and CO<sub>2</sub> Capture-Assisted Methane Production

Advances in Resources Recovery of H2S: A Review of Desulfurization Processes and Catalysts

Research Progress of Removal of H2S from Coal Gas by Dry Method

Simulation of H2S and CO2 Removal from IGCC Syngas by Cryogenic Distillation

CO2 Removal in Hydrogen Production Plants

Process simulations of blue hydrogen production by upgraded sorption enhanced steam methane reforming (SE-SMR) processes

Research progress of hot gas filtration, desulphurization and HCl removal in coal-derived fuel gas: A review