Abstract:This study explores the precision micro-machining of CoCrFeNiAlX short fiber-reinforced 7A09 aluminum matrix composites, focusing on the interplay between machining parameters and composite properties. The investigation scrutinizes the influence of vibrational amplitude, oscillation frequency, penetration depth, fiber orientation, and aluminum concentration on machining dynamics. Findings reveal that enhancing the X-axis vibrational amplitude to 80 μm is associated with a decrease in machining force, which then rises after reaching a threshold. In contrast, maintaining the Y-axis amplitude below 90 μm significantly increases the machining force. Higher amplitudes and frequencies were observed to reduce machining forces by up to 57% at an ultrasonic frequency of 15 kHz. Employing ultrasonically assisted vibration cutting (UEVC) culminated in a substantial 72% decrease in machining forces when fibers were optimally oriented at 45°. The study also identifies a direct correlation between the cutting temperature and both the vibrational amplitude and penetration depth, with the Y-axis amplitude having a more significant impact, causing a 55% variation in temperature. An increase in frequency initially lowers the cutting temperature, with the lowest temperature of 92 °C achieved at 5 kHz, while the peak temperature occurs at a machining depth of 60 μm. Temperature profiles indicate an initial rise with increased fiber orientation, followed by a decline. A slight increase in aluminum concentration marginally raises the cutting temperature. Furthermore, UEVC is found to produce a parabolic residual stress distribution, where amplitude and penetration depth determine the peak stress levels, and higher frequencies contribute to stress reduction. Fiber orientation also affects residual stress, with proper alignment reducing compressive stress and misalignment increasing it. The lowest point of residual compressive stress is detected in the Al0.6 fiber composite, while the peak is observed in the Al1 composites.

Effect of axial ultrasonic vibration on the surface topography and microstructure of Al6061 chip in extrusion cutting

Micro Pin Extrusion of Metallic Materials Assisted by Ultrasonic Vibration

Study on Ultra-Precision Processing of Ti-6Al-4V with Different Ultrasonic Vibration-Assisted Cutting Modes

Investigation on the micro-cutting mechanism of aluminum matrix composites with ultrasound elliptical vibration

Ultrasonic Elliptical Vibration Texturing of the Rake Face of Carbide Cutting Tools for Adhesion Reduction

Theoretical and experimental investigation of ultrasonic cutting kinematics and its effect on chip formation and surface generation in high-frequency ultrasonic vibration-assisted diamond cutting

Analytical modelling and experimental study of surface roughness in ultrasonic elliptical vibration assisted ultra-precision cutting of Ti-6Al-4 V alloy

Effect of UEVC parameters on cutting surface quality and subsurface damage of single crystal γ-TiAl alloy via atomic simulation

Effects of ultrasonic vibration cutting trajectories on chip formation of tungsten alloys

Promoted grain refinement in tool-chip interface during ultrasonic elliptical vibration-assisted cutting of polycrystalline copper

Investigation of Surface Integrity of Selective Laser Melting Additively Manufactured AlSi10Mg Alloy under Ultrasonic Elliptical Vibration-Assisted Ultra-Precision Cutting

Effects of Ultrasonic Vibration Assistance on Chip Formation Mechanism in Cutting of Ti–6Al–4V

Experimental and simulation investigation of ultrasonic elliptical vibration cutting of tungsten alloys in ultra-precision machining

Experimental Investigation on Micro-Groove Manufacturing of Ti-6Al-4V Alloy by Using Ultrasonic Elliptical Vibration Assisted Cutting.

Ultrasonic elliptical vibration micro-cutting mechanism of CoCrFeNiAlX short fiber reinforced aluminum-based composite

Evolution Mechanism of Microstructure and Microhardness of Ti–6Al–4V Alloy During Ultrasonic Elliptical Vibration Assisted Ultra-Precise Cutting

Generation mechanism of surface micro-texture in axial ultrasonic vibration-assisted milling (AUVAM)

Optimizing Processing Parameters and Surface Quality of TC18 via Ultrasonic-Assisted Milling (UAM): An Experimental Study

Ultrasonic vibration-assisted milling of aluminum alloy

Experimental Study on Ultrasonic-Assisted End Milling Forces in 2195 Aluminum-Lithium Alloy

Research on cutting force and surface integrity of TC18 titanium alloy by longitudinal ultrasonic vibration assisted milling