Abstract:TC4 titanium alloy is utilized in aerospace and a wide range of other applications due to its high strength and corrosion resistance, but its poor thermal conductivity and high ductility introduce challenges in machining. In this paper, firstly, a mathematical model of workpiece surface morphology under tilted ultrasonic elliptical vibration cutting (TUEVC) was established based on the tip trajectory and material removal mechanism, and the variation of workpiece surface morphology was investigated at different tool tilt angles θ , and it was found that the tilt θ in a certain range could significantly reduce the surface residual height compared with that of ordinary ultrasonic elliptical vibration cutting (UEVC). Second, the TUEVC experiment of TC4 titanium alloy was carried out to comparatively analyze the changes in the surface morphology, surface profile, and surface roughness of the workpiece under different tilt θ , the effect of each machining parameter (cutting speed, feed, and ultrasonic amplitude) on surface roughness was explored. The experimental results indicate that as the tilt θ changes from 0° to 90° throughout the process, the workpiece surface morphology flatness decreases and then increases. When the tilt angle θ is 45°, workpiece cutting surface roughness is minimized ( Sa = 0.157), compared with the ordinary ultrasonic elliptical vibration cutting roughness is reduced by 47.6 % maximum. Both the surface morphology flatness and the surface roughness of the workpiece are at their smallest, whereas the theoretical profile curve and cutting surface profile curve are at their most consistent. Under the same machining parameters, TUEVC can reduce the surface roughness more effectively compared with UEVC, this technique reduces surface roughness by 16 %, 23 %, and 26 % at maximum for different cutting speeds, feeds, and ultrasonic amplitudes, respectively.

Effects of ultrasonic vibration cutting trajectories on chip formation of tungsten alloys

Surface/subsurface formation mechanism of tungsten during ultrasonic elliptical vibration cutting

Cutting Chatter in Ultrasonic Elliptical Vibration Cutting and Its Influence on Surface Roughness and Tool Wear

Effects of Ultrasonic Vibration Assistance on Chip Formation Mechanism in Cutting of Ti–6Al–4V

Ultrasonic Elliptical Vibration Texturing of the Rake Face of Carbide Cutting Tools for Adhesion Reduction

Study on design of conical arc side-edge milling cutter and cutting performance under ultrasonic-assisted condition

Insight into surface formation mechanism during ultrasonic elliptical vibration cutting of tungsten alloy by scratching experiment and molecular dynamics

Experimental investigations on ultrasonic elliptical vibration turning of SiCp/Al composites

Effect of cutting conditions on the serrated chip formation in high-speed cutting

Promoted grain refinement in tool-chip interface during ultrasonic elliptical vibration-assisted cutting of polycrystalline copper

Theoretical and numerical studies of surface microstructural transformation in ultrasonic elliptical vibration cutting tungsten heavy alloys

Study on Ultra-Precision Processing of Ti-6Al-4V with Different Ultrasonic Vibration-Assisted Cutting Modes

Research on cutting force and surface integrity of TC18 titanium alloy by longitudinal ultrasonic vibration assisted milling

Study on chip shapes in longitudinal-torsional composite ultrasonic vibration–assisted drilling of Ti-6Al-4V

Effect of cutting parameters on chips and burrs formation with traditional micromilling and ultrasonic vibration assisted micromilling

Ultraprecision Machining of Tungsten Alloy by Applying Ultrasonic Elliptical Vibration Cutting

Effect of axial ultrasonic vibration on the surface topography and microstructure of Al6061 chip in extrusion cutting

Theoretical and experimental investigation of ultrasonic cutting kinematics and its effect on chip formation and surface generation in high-frequency ultrasonic vibration-assisted diamond cutting

Effects of vibration trajectory on ductile-to-brittle transition in vibration cutting of single crystal silicon using a non-resonant tool

Generation mechanism of the surface morphology on tilted ultrasonic elliptical vibration cutting TC4 titanium alloy

Design Optimization of Ultrasonic Vibration Cutting Tool to Generate Well-Decoupled Elliptical Trajectory