Abstract:There is a great potential in using different techniques of additive manufacturing (AM) for the production and refurbishment of hot forming dies. In hot stamping of AlSi-coated boron steel, the dies are exposed to a complex combination of abrasive and adhesive wear. This results in tool damage and eventually tool refurbishment is necessary. Laser-metal-deposition (LMD) is an AM technique suitable for tool repairing due to its easier implementation, compared to selective-laser-melting (SLM). However, tribological studies on AM produced tools are still limited, particularly in the context of hot forming. Thus, the aim of this work is to increase the knowledge on the friction and wear behavior of LMD tool materials in hot stamping conditions. Two LMD materials were investigated: a hot-work tool steel (LMD-TS) and a conceptual high-hardness tool material (LMD-HH). Porosity was observed for both materials in the form of lack-of-fusion defects. LMD-TS resulted in a Vickers hardness value of approximately 650 HV, while LMD-HH showed a value of approximately 1100 HV. A high temperature strip drawing tribometer was used to perform friction and wear tests against AlSi-coated boron steel under unidirectional (linear) sliding conditions. Workpiece temperatures during sliding were 600°C and 700°C. All tribotests at 700°C resulted in severe adhesion and AlSi-coating rupture, resulting in higher and more unstable friction. The wear mechanisms observed for LMD-TS were a combination of abrasive and adhesive wear, where ploughing and grooving in the tool material resulted in larger surface defects to accumulate material transfer. At 700°C, these mechanisms were more severe. LMD-HH did not show significant abrasive damage in any test; the resulting material transfer was thinner and sparser compared to the other LMD material. The change in FeAlSi material transfer for LMD-HH was associated with the reduction in abrasive damage, i.e., ploughing and grooving in the tool material did not take place and thus did not enhance material transfer. The LMD process itself did not seem to have either a positive or a negative effect on the tribological behavior of the tool materials in this tribosystem, and the differences are seen mostly from the hardness perspective. LMD-HH is a promising tool material to reduce wear in hot stamping dies.

High temperature friction and wear of hot stamping tool materials produced by laser metal deposition

Tribological Behavior of Laser Textured Hot Stamping Dies

Effect of preheating during laser metal deposition on the properties of laminated bending dies

Hybrid laser metal deposition of a Fe–Cr–Mo–V–Mn tool steel for hot stamping applications

Experimental and Numerical Study on Friction and Wear Performance of Hot Extrusion Die Materials

Adapting the Surface Integrity of High-Speed Steel Tools for Sheet-Bulk Metal Forming

Potential of high-feed milling structured dies for material flow control in hot forming

Tribological performance of 410L martensitic stainless steel parts manufactured by Laser directed energy deposition

Microstructure, abrasive wear and corrosion characterisation of laser metal deposited Fe-30Cr-6Mo-10Ni-2.2C alloy

High-Temperature Mechanical Properties of Stress-Relieved AlSi10Mg Produced via Laser Powder Bed Fusion Additive Manufacturing

Influence of hot forming on microstructure and mechanical properties of laser tailor-welded dissimilar ultra-high-strength steels

Tribological Performance of Additively Manufactured AISI H13 Steel in Different Surface Conditions

Local laser softening of press-hardened steel at high feed rates

Wear Behavior of AlSi10Mg Alloy Produced by Laser‐Based Powder Bed Fusion and Gravity Casting

Design of a Test Rig for the Characterization of Thermal Fatigue and Soldering Resistance of the Surfaces of Tool Steels for High‐Pressure Die‐Casting Dies

Influence of Abrasive Materials in Fluidised Bed Machining of AlSi10Mg Parts Made through Selective Laser Melting Technology

Pilot Demonstration of Hot Sheet Metal Forming Using 3D Printed Dies

Experimental and Computational Thermal Analysis of Ti-Based Alloy Produced by Laser Metal Deposition Technique

Laser melting deposited a laminated H13/17–4PH heterostructure alloy to achieve strength-ductility synergy and outstanding high-temperature wear resistance

The effects of hot forging on the preform additive manufactured 316 stainless steel parts

Laser Metal Deposition of Ti6Al4V—A Brief Review