Abstract:Al-Cu alloys are widely applied in the automobile and aircraft industries because of their low density, good wear resistance, low cost, and excellent mechanical properties. Microalloying, particularly using Mn, can further enhance the mechanical properties. Thus, a combination of high-angle annular dark-field scanning transmission electron microscopy, STEM-EDX elemental mapping, and tensile tests were used to investigate the effects of Mn content on the nucleation, growth, and structural evolution of θ'-Al 2 Cu and Mn-rich precipitation phases of Al-4Cu- x Mn alloys ( x = 0.1 wt.%, 0.2 wt.%, 0.3 wt.%, and 0.5 wt.%). The results revealed that adding Mn to Al-Cu alloys can effectively promote the precipitation of θ'-Al 2 Cu; particularly, increasing Mn content from 0 wt.% to 0.2 wt.% reduced precipitate size and size distribution. Moreover, the 0.3-wt.% Mn addition reduced θ′-Al 2 Cu precipitation and coherent Mn-rich phase precipitation with butterfly contrast in the alloy. The addition of 0.5-wt.% Mn resulted in disappearance of the θ'-Al 2 Cu phase and precipitation of a rod-like Mn-rich phase in the alloy, which was found to have coherent and semi-coherent interfaces with an Al matrix. Promotion of precipitation and refinement in the θ′-Al 2 Cu phase is primarily attributed to the excellent miscibility and interfacial segregation of the Mn element, which effectively enhanced heterogeneous nucleation in the θ′-Al 2 Cu phase. Additionally, two morphologies of the Mn-rich phase exhibited a relatively large coherence area with the matrix relative to θ′-Al 2 Cu; thus, our study provides a new strengthening and toughening technique for Al alloys.

A diffusion-based understanding on the effect of trace Mn and Zr addition in the precipitate coarsening kinetics of Al-Cu alloy

Partitioning and Diffusion of Transition Metal Solutes in Ternary Model Ni-based Single Crystal Superalloys

Effect of Interactions Between Elements on the Diffusion of Solutes in Ni X Y Systems and Γ′-Coarsening in Model Ni-based Superalloys

Unraveling L1 2 Al 3 X (X=Ti, Zr, Hf) Nano-Precipitate Evolution in Aluminum Alloys via Multi-scale Diffusion Simulation

Influence of Mg, Ag and Zn minor solute additions on the precipitation kinetics and strengthening of an Al-Cu-Li alloy

Influence of Mn Addition on the Evolution of Precipitates in Al-Cu Alloys

Effect of rare earth samarium addition on the kinetics of precipitation in Al-Cu-Mn casting alloy

High-throughput pseudo-binary diffusion couple approach for alloy design in cobalt-based superalloys

Effect of Zr addition on the microstructure evolution and mechanical properties of extruded Al-Cu-Li-Mn alloys

Precipitation in Al-Zr-Sc alloys: a comparison between kinetic Monte Carlo, cluster dynamics and classical nucleation theory

Atomic-scale investigation of interactions between Cu solute and defects in Zr alloys

Molecular dynamics simulation of diffusion in supercooled Cu–Zr alloys

An experimental study of the effect of Ag, Cu, Li, Mg, Ni, Ti, Sc, Zr on grain refining in binary and multicomponent Al-based alloys

Atomic-scale study on core-shell Cu precipitation in steels: atom probe tomography and ab initio calculations

Interdiffusion and Atomic Mobility in BCC-A2 Mo-Zr and Mo-Nb-Zr Alloys with Very Steep Composition Profiles

Enhanced Metastable Solubility by Ball Milling of Rapidly Solidified Cu-Co-Mn Ribbon

Study of the influence of alloying elements on Cu precipitation in steel by non-classical nucleation theory

The role of Sn trace addition in the precipitation behavior and strengthening of the wrought Al–Cu–Mn-based alloy

Experimental and theoretical study of tracer diffusion in a series of (CoCrFeMn)$_{100-x}$Ni$_x$ alloys

Effects of Fe, Cr and Mn on inter-diffusion in CoNi-containing multiple principal alloys

Microstructure and properties of a Cu–Cr–Zr alloy