Abstract:Elemental powder blends with atomic composition of Cu 100− x Ta x ( x =10, 30, 50, 70, and 90) were ball milled in a SPEX mill at several temperatures (room temperature (RT), liquid nitrogen temperature (LN 2 T), −80 °C, and 95 °C) to examine the effect of milling temperature on the extent of alloying and microstructural refinement. For the Cu-rich powders (10< x <50), high-energy ball milling to steady state at all temperatures produced a mixture of nanocrystalline Cu and Ta with no observable extension of mutual solid solubility. Compared with milling at RT, cryomilling (LN 2 T) caused further refinement of Cu crystallites, while the same steady-state grain size was reached for Ta crystallites. On the Ta-rich side (50< x <90), ball milling at all temperatures led to refined Cu and Ta grain sizes. Partial amorphization seemed to be present, which apparently increased in extent with increasing contamination from the milling media upon extended milling. Very similar results were obtained for milling at RT and LN 2 T. It was concluded that high-energy ball milling at LN 2 T did not drastically enhance the amorphization reaction between Cu and Ta nor extend their mutual solubility. The limited power of cryomilling to alloy immiscible elements such as Cu-Ta is explained as a consequence of the inability to fully suppress, during energetic collisions, the atomic mobility responsible for phase separation even when the milling is conducted at the nominal LN 2 T. The temperature dependence of milling-induced microstructural refinement and alloying is analyzed in terms of the dynamics of the generation and annihilation of the nonequilibrium vacancies in an externally driven system. It is predicted that externally forced mixing as well as diffusion assisted by high-energy ball milling can be merely weakly temperature dependent between RT and LN 2 T. As a result, the extension of solubility by using cryomilling is feasible only in limited systems, and this process cannot be expected to alloy all immiscible elements.

Enhanced Metastable Solubility by Ball Milling of Rapidly Solidified Cu-Co-Mn Ribbon

Effect of free energy on the solid solubility and magnetic behaviour of a mechanically alloyed nanocrystalline Cu–Co–Ti alloy

Enhancing microstructure and magnetic properties of ribbons of Cu–Co–Ti alloy through ball milling: experimental insights and theoretical perspectives

Effect of Minor Addition of Co on Nonequilibrium Solidification of Deeply Undercooled Cu Based Alloys

Rapid Solidification Structure Refinement Mechanism in Highly Undercooled Cu Based Ternary Alloys

Eff ects of Diff erent Mechanical Alloying Parameters on Microstructure of High Temperature Nanocrystalline Cu-Ta Alloys

Study on the Solid Solubility Extension of Mo in Cu by Mechanical Alloying Cu with Amorphous Cr(Mo)

Extension of Solid Solubility and Structural Evolution in Nano-Structured Cu-Cr Solid Solution Induced by High-Energy Milling.

Crystallization Kinetics of Co-Finemet Amorphous Alloys and Magnetic Properties of Nanocrystalline Powder Cores

Properties and microstructural evolution of a ternary Cu–Co–Fe immiscible alloy solidified under high magnetic fields

Crystallization Kinetics and Magnetic Properties of Fe73.5si13.5b9cu1nb1v2 Nanocrystalline Powder Cores

Effect of Co Addition on Solidification Velocity, Hardness and Refined Structure Transformation Mechanisms of Undercooled Ni-Cu-Co Alloys

In situ synchrotron diffraction and modeling of non-equilibrium solidification of a MnFeCoNiCu alloy

Alloying Effects on the Microstructure and Mechanical Properties of Nanocrystalline Cu-based Alloyed Thin Films: Miscible Cu-Ti Vs Immiscible Cu-Mo

Tailoring the microstructure and properties of a Cu–Co immiscible alloy by high magnetic field assisted heat treatment

Overlapping Solid Solubility In Mechanically Alloyed Fe-Ni And Fe-Cu

Co effect on rapid solidification microstructure transition of highly undercooled copper alloys

Effect of milling temperature on mechanical alloying in the immiscible Cu-Ta system

Synchrotron X-ray Absorption Studies of Atomic-Level Alloying in Immiscible Mixtures

Rapid Solidification of Cu60Co30Cr10 Alloy under Different Conditions

63Cu Nuclear Magnetic Resonance Analysis of Mechanical Alloying Processes in Copper-Zinc Powders