Abstract:Novel nanocomposites based on an AZ91 magnesium alloy matrix reinforced with a hybrid mixture of SiC and TiC nanoparticles with different nanoparticle contents (0.5% and 1%, by mass fraction) were fabricated by semi-solid stirring followed by ultrasonic vibration. Microstructural analysis indicated that the hybrid nanoparticles were uniformly distributed in the nanocomposite. The morphology of the Mg17Al12-based eutectic phase changed from plate-like, in the as-cast AZ91 alloy, to lamellar in the as-cast nanocomposites. The tensile strength and micro-hardness of the nanocomposites were improved by increasing the fraction of nanoparticles in the composite. Following extrusion, the matrix grains in the nanocomposite were significantly refined. The extent of the grain refinement increased at higher mass fractions of the nanoparticle. This refinement was not only due to dynamic recrystallization, but also the synergistic pinning effects arising from both the externally added nanoparticles as well as dynamically precipitated Mg17Al12 particles. The nanoparticle additions led to increases in yield strength (YS), ultimate tensile strength (UTS) and elongation to failure (EL). The increase in YS was mostly attributed to the effects of grain refinement, with additional contributions from the influence of Orowan strengthening and thermal expansion effects. The values of both the work hardening rate (θ) and strain hardening exponent (n) increased with increasing fraction of nanoparticles. The high θ value in stage III was attributed to both grain refinement and weakening of the basal plane texture, while the high n value was mainly related to the increase in resistance to dislocation movement caused by pinning effects of the nanoparticles.

Overcoming Oxidation and Enhancing Dispersion of Nanoparticles Via Molten Salt: Configurational Distribution of TiCnp in Pure Mg

Enhancing Dispersion of TiB2 Nanoparticles in Al Composites Via Ultrasonic-Assisted Fast Cooling Schemes

Molten Salt Assisted Solidification Nanoprocessing of Al-TiC Nanocomposites

In-situ Synthesis of Nanocrystalline TiC Powders, Nanorods, and Nanosheets in Molten Salt by Disproportionation Reaction of Ti(II) Species

A New Technique for Dispersion of Carbon Nanotube in A Metal Melt

Strengthening and Toughening Mechanisms of Mg Matrix Composites Reinforced with Specific Spatial Arrangement of In-Situ TiB2 Nanoparticles

A New Sight on the Influence of Molten Salt in the Preparation of (ta, Nb, Ti) C Nanopowder

A Novel Melt Processing for Mg Matrix Composites Reinforced by Multiwalled Carbon Nanotubes

Interplay between interfacial layer and nanoparticle dispersion in molten salt nanofluid: Collective effects on thermophysical property enhancement revealed by molecular dynamics simulations

Synergistic effects of hybrid (SiC+TiC) nanoparticles and dynamic precipitates in the design of a high-strength magnesium matrix nanocomposite

Nanoparticulate Dispersion, Microstructure Refinement and Strengthening Mechanisms in Ni-coated SiCp/Al-Cu Nanocomposites

Effect of Mg on the microstructure evolution and mechanical properties of 5%TiB2/Al−4.5%Cu composites

AZ91D/TiB2 Nanocomposites Fabricated by Solidification Nanoprocessing

High Strength TiCp/Mg-Zn-Ca Magnesium Matrix Nanocomposites with Improved Formability at Low Temperature

Enhanced ductility by Mg addition in the CNT/Al-Cu composites via flake powder metallurgy

Wet Powder Metallurgy Process for Dispersing Carbon Nanotubes and Fabricating Magnesium Composite

On the Origin of Strengthening Mechanisms in Ni-Mo Alloys Prepared Via Powder Metallurgy

Synergistic Optimization in Solidification Microstructure and Mechanical Performance of Novel (tic N − TiB2)p/Al Nanocomposites: Design, Tuning and Mechanism

The Influence of Nanoparticles on Dendritic Grain Growth in Mg Alloys

Stable Dispersion of Carbon Nanotubes in a Molten Salt of KNO3-NaNO3-NaNO2-LiNO3-LiOH.

Improvement in hydrogen storage performance of Mg by mechanical grinding with molten salt etching Ti3C2Clx