Abstract:The object of this study is to investigate the structure of cast magnesium alloy (Mg-Al-Zn) inoculated with nano particles of different allotropic forms of carbon. The aim of this study is to improve the processability and quality of critical load bearing magnesium alloy part castings. The tasks of the study are: attainment of efficient control of the alloy structural features by introduction of incremental additions of carbon nano particles; determination of the relationship between the quantity of the added inoculating carbon agent and α - solid solution grain size; determination of the influence of allotropic forms of carbon on the morphologic characteristics of the intergranular borders and the eutectoid (a+Mg17Al12); and comparative analysis of the phase composition of the standard ML5 alloy and the experimental alloy ML5 inoculated with carbon black, nanographite, and single-wall carbon nanotubes. The phase composition was determined by X-ray diffraction analysis using copper radiation. Micro X-ray spectral analysis was performed. The following findings were obtained. Using an optical microscope α – solid solution grain size was measured in the standard and inoculated alloy. In the samples of the alloy variants inoculated with 0.1 % wt. of carbon black, nanographite, and single-wall carbon nanotubes, the grain size was reduced by appox. 50 % compared with the standard alloy. In the samples of the alloy inoculated with 0.1 % wt. of nanographite and single wall carbon nanotubes, eutectoid (a+Mg17Al12) precipitates along the grain boundaries were thinner than those in the standard alloy samples and those inoculated with carbon black. X-ray diffraction analysis revealed no new phase formation. The X-ray diffraction patterns of the alloy samples with nanographite and nanotubes display weak peaks of free carbon, which may indicate the presence of free carbon in small quantities in the structure. The scientific and practical originality of the obtained results consists of the following: a technology of inoculation with incremental additions of allotropic forms of nano carbon, namely carbon black, nanographite, and single-wall carbon nanotubes, has been tested on a standard cast magnesium alloy (Mg-Al-Zn system) in an environment similar to the industrial production of critical magnesium cast components. It has been shown that the introduction of nanocarbon in a quantity of 0.1 % wt. can have a beneficial effect on the structural characteristics of ML5 cast magnesium alloy with no change in its phase composition. Nanographite and single wall carbon nanotubes with a regular structure contribute to the formation of thinner intergranular boundaries than amorphous carbon black.

The Influence of Nanoparticles on Dendritic Grain Growth in Mg Alloys

Effect of Mg on Nucleation Process of Recrystallization in Al–Mg–Si/SiCp Composite

Synchrotron Tomographic Quantification of the Influence of Zn Concentration on Dendritic Growth in Mg-Zn Alloys

Dendritic Evolution During Coarsening of Mg-Zn Alloys Via 4D Synchrotron Tomography

Fast Synchrotron X-Ray Tomographic Quantification of Dendrite Evolution During the Solidification of Mg-Sn Alloys

Dendritic Growth in Mg-Based Alloys: Phase-Field Simulations and Experimental Verification by X-ray Synchrotron Tomography

Engulfment and distribution of second-phase nanoparticle during dendrite solidification of an Al–Si binary alloy: a simulation study

Dendritic morphology of α-Mg during the solidification of Mg-based alloys: 3D experimental characterization by X-ray synchrotron tomography and phase-field simulations

RESEARCH PROGRESS ON 3D DENDRITE MORPHOLOGY AND ORIENTATION SELECTION DURING THE SOLIDIFICATION OF Mg ALLOYS: 3D EXPERIMENTAL CHARACTERIZATION AND PHASE FIELD MODELING

Observation of Dendrite Growth Velocity and Microstructure Transition in Highly Undercooled Single Phase Alloys

The effect of cross-section geometry of castings on dendrite evolution in Mg Gd alloys by in situ X-ray radiography

A Phase-Field Study on the Effects of Nanoparticles on Solidification and Grain Growth

Atomic-scale inhomogeneous solute distribution in an ultrahigh strength nanocrystalline Al-8 Mg aluminum alloy

Bulk nanocrystalline Al alloys with hierarchical reinforcement structures via grain boundary segregation and complexion formation

Influence of carbon nanoparticle inoculation on the structure of ML5 casting magnesium alloy

Microstructure refinement and mechanical properties enhancement of Mg Al alloys via a novel of MgO nanoparticles modified graphene nanoplates refiner by in-situ synthesis

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles

Unraveling Thermodynamic and Kinetic Contributions to the Stability of Doped Nanocrystalline Alloys using Nanometallic Multilayers

Grain growth and strengthening mechanisms of ultrafine-grained CoCrFeNiMn high entropy alloy matrix nanocomposites fabricated by powder metallurgy

Synergistic effects of hybrid (SiC+TiC) nanoparticles and dynamic precipitates in the design of a high-strength magnesium matrix nanocomposite

Effect of Adding AlN Ceramic Particles on the Micromorphology of the Mg 17 Al 12 Phase in Magnesium Alloys