Abstract:Introduction Solid state batteries offer increased safety, high voltage stability, and simpler electrolyte chemistry than organic electrolytes. Their inherent protection from dendrite growth gives the capability to use metallic lithium anodes. Recent advances have improved conductivity to within an order of magnitude of organic electrolytes at room temperature. However, interfacial resistance between electrodes and the electrolyte remains a pressing concern. In a typical planar battery, this high resistance per area is magnified by low interfacial surface area. Elemental composition has a significant effect on the conductivity of a garnet electrolyte. The conductivity of the garnet fluctuates an order of magnitude based on a lithium stoichiometry of 6 to 7 in the Li7-xLa3Zr2-xTaxO12series. It has also been demonstrated that aluminium composition at the grain boundaries associated with higher temperature sintering increases conductivity. It stands to reason lithium activity extremes at the electrode interfaces effects would cause local variations in electrolyte composition and affect the conductivity. This study aims to address some of these concerns using a systematic study of the anode-electrolyte interface and the cathode-electrolyte interface. We investigate the elemental composition of the interface, as well as the effect of greatly increased surface area through a highly microporous electrolyte scaffold containing the cathode and anode material. Experimental Procedure Li7La3Zr2O12 garnet was produced in a conventional solid state method. 10% excess LiOH-H2O and stoichiometric amounts of La2O3 and ZrO2were ball milled in ethanol for 24 hours. The milled materials were added to an alumina crucible, calcined at 900 ºC for 4 hours, and milled again. A colloidal deposition of this slurry is prepared with polyvinyl butyral (PVB), benzyl butyl phthalate (BBP), and Solsperse dispersant in ethanol. Calcined powder is added to toluene and ethanol solvents with a binder system containing PVB, BBP, and menhaden fish oil as a dispersant. This preparation is milled for two days, then degassed in preparation for tape-casting. After tape-casting, tapes are drop-coated with the colloidal slurry and another tape is applied on top. This structure is held at 500ºC for 1 hour to burn off binders then heated to 1100 ºC for 1 hour. This produces a three layer porous-dense-porous scaffold of electrolyte that will maintain electronic isolation between electrodes. Symmetric cells with two cathodes are produced by infiltrating a glycine/metal-nitrate solution into the pores of each side and combusting. For two-anode symmetric cells, lithium is lightly pressed into both sides at 350 ºC. Electrochemical impedance spectroscopy was performed between room temperature and 300 ºC using a 10 mV amplitude between 10 MHz and 100 mHz. Electron energy loss spectroscopy was performed on a 2100F TEM equipped with a Gatan Tridiem post-it column energy filter. Results Figure 1 shows a cross section of a lithium-penetrated Li-garnet scaffold showing the fracture plane of the garnet(light) fully coated by the lithium (dark). Figure 2 shows the Nyquist plot of a full cell made with a lithium-penetrated scaffold. The bulk conductivity shown in the inset is fairly low at 20 Ω compared to the 1000 Ω overall cell impedance.

The origin of high electrolyte–electrode interfacial resistances in lithium cells containing garnet type solid electrolytes

Effect of H+ Exchange & Surface Impurities on Bulk & Interfacial Electrochemistry of Garnet Solid Electrolytes

Interrelated interfacial issues between a Li 7 La 3 Zr 2 O 12 -based garnet electrolyte and Li anode in the solid-state lithium battery: a review

Probing into the origin of an electronic conductivity surge in a garnet solid-state electrolyte

Microscopic Origin of the Ionic Transport Behaviors in Solid Electrolytes for Li Batteries

Interrelated interfacial issues between a Li<sub>7</sub>La<sub>3</sub>Zr<sub>2</sub>O<sub>12</sub>-based garnet electrolyte and Li anode in the solid-state lithium battery: a review

Negating Interfacial Impedance in Garnet-Based Solid-State Li Metal Batteries

Effect of Microstructure and Elemental Composition on Electrode Interfacial Impedance of Li7La3Zr2O12-based Batteries

In Situ Fabrication of High Ionic and Electronic Conductivity Interlayers Enabling Long-Life Garnet-Based Solid-State Lithium Batteries

Impact of Air Exposure and Surface Chemistry on Li-Li7la3zr2o12 Interfacial Resistance

Inhibiting Formation and Reduction of Li2 CO3 to LiCx at Grain Boundaries in Garnet Electrolytes to Prevent Li Penetration.

The Interface Between Li6.5La3Zr1.5Ta0.5O12 and Liquid Electrolyte

Interrelated Interfacial Issues Between A Li7la3zr2o12-Based Garnet Electrolyte And Li Anode In The Solid-State Lithium Battery: A Review

Quasi- In Situ XPS Insights into the Surface Chemistry of Garnet-Type Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 Solid-State Electrolytes: The Overlooked Impact of Pretreatments and a Direct Observation of the Formation of LiOH

Enhanced Performance of Li6.4La3Zr1.4Ta0.6O12 Solid Electrolyte by the Regulation of Grain and Grain Boundary Phases.

Origin of Lithiophilicity of Lithium Garnets: Compositing or Cleaning?

Inhibiting Formation and Reduction of Li2CO3 to LiCx at Grain Boundaries in Garnet Electrolytes to Prevent Li Penetration

Reducing Impedance at a Li-Metal Anode/Garnet-Type Electrolyte Interface Implementing Chemically Resolvable In Layers

Interrelationships among Grain Size, Surface Composition, Air Stability, and Interfacial Resistance of Al-Substituted Li7La3Zr2O12 Solid Electrolytes

Atomic-Scale Engineering of Grain Boundary Chemistry and Potential for Li-Garnet Solid-State Electrolytes

Garnet-type Solid-state Electrolyte Li7La3Zr2O12: Crystal Structure, Element Doping and Interface Strategies for Solid-state Lithium Batteries