Abstract:Supercritical carbon dioxide is one of the most promising candidate working fluids for nuclear power plants.Structural materials using in this kind of system face severe challenges due to its high temperature and high pressure.Corrosion,especially oxidation and carburization,will occur,which leads to the failure of material.Tradi-tional metallic materials like austenitic stainless steel,which is regarded as the candidate cladding materials,will break away because of their limited properties.To further improve the corrosion resistance of austenitic stainless steel as the candidate cladding material for supercritical carbon dioxide nuclear reactor,the general corrosion behavior of three kinds of alumina-forming austenitic stainless steel with different Al contents and their Al-free steel was investigated in supercritical carbon dioxide at 650 ℃/20 MPa.The purity of carbon dioxide was 99.99％.All samples were firstly ground,and then polished to eliminate the surface damage regions.Scanning electron microscopy equipped with backscattered electron,electron backscatter diffraction detector and energy disper-sive spectroscopy was used for microanalysis.Focused ion beam system was used to prepare the cross-sectional transmission electron microscopy foils.Selected area electron diffraction was also carried out on the transmission electron microscopy foils for revealing the detailed microstructural characterization.Glow discharge optical emission spectrum was used for carburization analysis.The results show that the weight gain of materials decreases with the increase of Al content,and the weight gain of 3.5wt％Al steel is only about 0.022 mg/cm2.The weight gain against exposure time of different materials follows the parabolic growth law approximately,which indicates that the corrosion behavior is mainly controlled by diffusion.When the content of Al is less than 1.5wt％,a dual-layer Fe-rich oxide film is formed on the surface with poor protection.Some pores were observed within it,which can cause oxidation and carburization.Carburization occurs on Al-free steel and the depth of the carburization region can be up to about 12 µm.When the content of Al is higher than 2.5wt％,protective oxide films are formed on the surface.Its outer layer is mainly rich in Cr and the inner layer is rich in Al.The Al layer on 2.5wt％and 3.5wt％Al containing steel is more continuous.These oxides own better corrosion resistance than that formed on 1.5wt％steel.Although more protective oxides are formed,carburization still exists in the oxide film and matrix of this kind of materials,while the thickness of the carburization region decreases to about 6 μm.Higher Al content,above 2.5wt％,can effectively facilitate the formation of protective Al-rich oxide film,which hinders the outward diffusion of Fe and the inward diffusion of C.It further improves the oxidation and carburizing resist-ance of materials,which will be useful in the supercritical carbon dioxide nuclear power plant.

Effect of Al Content on Mechanical Properties and Corrosion Performance of Novel Fe-Cr-Al Alloy Steels in a CO2-O2 Coexistence Environment

Microstructures, Tensile Properties and Corrosion Behaviors of Fe20Cr25NiNb Stainless Steels with Different Al Contents in Supercritical Carbon Dioxide

Effect of Co Content on the Microstructure and Corrosion Behavior of Al0.3CoxCrFeNi High Entropy Alloys

Corrosion of Fe-Ni-Cr Alloys with Various Aluminum Additions in a Carburizing-Oxidizing Atmosphere at 900 °C

Effect of carbon content on microstructure,mechanical properties and intergranular corrosion resistance of 0 Cr25 Ni35 AlTi alloy

Effect of Al content on the microstructure and properties of CoCrCuFeNiMoAlx high entropy alloy

Investigating the effect of Cr content on the microstructure and electrochemical measurement of low alloy steel

Effect of Al alloying on corrosion performance of steel

Effect of 4 wt.% Cr on microstructure, corrosion resistance and tribological properties of Fe3Al-20 wt.%Al2O3 composites

Effect of Al content in CoCrFeNiAl x HEA on mechanical properties and high temperature oxidation resistance of WC-10%CoCrFeNiAl x hard alloy

Effect of Cr on the Microstructure and Oxidation Properties of Co-Al-W Superalloys Studied by in Situ Environmental TEM

Effect of Fe on the Oxidation, Sulfidation and Carburization Behaviors of Alloys in CO2 Containing SO2

Atomic Insights into the Corrosion Behavior of Fe-Cr Alloys in Supercritical CO2 Environment

Corrosion behaviors of CoCrWAlx alloys by laser additive manufacturing in molten Al

Corrosion Behavior of Newly Designed Fe-Ni-Base Alloys in High-Temperature CO2 at 700 °C

Effect of Al on the microstructure and corrosion resistance of high-Mn steel

Effects of Al addition on high temperature oxidation behavior of 16Cr ODS steel

Effect of Al Content on General Corrosion Behavior of Alumina-forming Austenitic Stainless Steel in High Temperature Supercritical Carbon Dioxide

Effect of Alloying Elements Cr and Al on ElectrochemicalCorrosion Behavior of J55 Steel

Effect of Al Addition on Microstructure and Properties of CoCrNi Medium-Entropy Alloy Prepared by Powder Metallurgy

Effect of Al content on steam oxidation behavior for ferritic Fe-21Cr-xAl alloys