Abstract:Molybdenum disulfide (MoS2) is a promising anode material for lithium-ion batteries (LIBs) due to its distinctive graphene-like structure and high specific capacity. However, its commercial application is hindered by the severe volume expansion during lithiation/delithiation and poor conductivity. In this paper, we report a facile one-pot enhanced hydrothermal synthesis strategy to prepare high-performance MoS2/C composite materials. The results indicate that the as-prepared MoS2/C composite is a subspheroidal core–shell structure material, with uniform coating, good particle dispersion, and an average grain size of approximately 80 nm. The morphology of the composite remained unchanged even after annealing at 500 °C for 2 h. The addition of glucose can accelerate the nucleation and growth of MoS2, and higher hydrothermal temperatures can improve the product yield. The addition of PVP has little effect on the yield, but significantly reduces the particle size. The XPS analysis reveals that the MoO3 may be generated as an intermediate product during the hydrothermal process. The electrochemical test results show that the unannealed MoS2/C samples exhibit discharge-specific capacities of 705.2 mAh·g−1 and 625.7 mAh·g−1 after the first cycle and the 100th cycle, respectively, at a current density of 500 mA·g−1, with a capacity retention rate of 88.7%. In contrast, the specific capacity of the MoS2/C specimens after annealing at 500 °C for 2 h shows a tendency to decrease and then slowly increase during the cycles, and the discharge specific capacity is 582.3 mAh·g−1 after the 100th cycle, which is lower than that of the unheated sample. The impedance analysis reveals that the lithium-ion diffusion coefficient of the MoS2/C material without calcination is 2.11 × 10−18 cm·s−2, which is superior to that of the annealed MoS2/C and pristine MoS2 samples. This characteristic is favorable for lithiation/delithiation during the charge/discharge process.

Microstructures and Properties of Honeycomb Sulfur/carbon Black/MoS2 Composites

From Dispersed Microspheres to Interconnected Nanospheres: Carbon-Sandwiched Mono Layered Mos2 As High-Performance Anode of Li-Ion Batteries

Facile and Scalable Synthesis of Micro-Mesoporous Carbon/magnesium Oxide/sulfur Composite for Lithium-Sulfur Batteries

Core-shell Structure of Hierarchical Quasi-Hollow MoS2 Microspheres Encapsulated Porous Carbon As Stable Anode for Li-ion Batteries.

Catalytic Mo2C decorated N-doped honeycomb-like carbon network for high stable lithium-sulfur batteries

Honeycomb-like Nitrogen and Sulfur Dual-Doped Hierarchical Porous Biomass-Derived Carbon for Lithium-Sulfur Batteries

Enhanced polysulfide regulation via honeycomb-like carbon with catalytic MoC for lithium–sulfur batteries

Naturally derived honeycomb-like N,S-codoped hierarchical porous carbon with MS2 (M = Co, Ni) decoration for high-performance Li-S battery

Synthesis and Characteristics of Nanoporous Carbon Spheres /S Composite as Cathode Material for Li-S Battery

Preparation and Properties of Sulfur/Mesoporous Carbon Composite Cathode Materials

Preparation and Electrochemical Properties of MoS2/C Hollow Microspheres

A Mixed Microporous/Low-range Mesoporous Composite with High Sulfur Loading from Hierarchically-structured Carbon for Lithium Sulfur Batteries

Low-Cost Synthetic Honeycomb-like Carbon Derived from Cotton as a Sulfur Host for the Enhanced Electrochemical Performances of Lithium–Sulfur Batteries

Unveiling the Influences of In Situ Carbon Content on the Structure and Electrochemical Properties of MoS2/C Composites

One-Pot Hydrothermal Synthesis and Electrochemical Performance of Subspheroidal Core–Shell Structure MoS2/C Composite as Anode Material for Lithium-Ion Batteries

A novel honeycomb-like WS2-x/CoS@C composite as anode for lithium ion batteries

Investigation of the Nanocrystal CoS 2 Embedded in 3D Honeycomb-like Graphitic Carbon with a Synergistic Effect for High-Performance Lithium Sulfur Batteries.

Facile Synthesis of Porous Li2S@C Composites As Cathode Materials for Lithium–sulfur Batteries

A hierarchical micro/mesoporous carbon fiber/sulfur composite for high-performance lithium-sulfur batteries

MoS<sub>2</sub>/carbon composites prepared by ball-milling and pyrolysis for the high-rate and stable anode of lithium ion capacitors

In Situ Synthesis of Homogeneous Ce2S3/MoS2 Composites and Their Electrochemical Performance for Lithium Ion Batteries