Abstract:So far, intrinsic hydrogenated amorphous silicon (a-Si:H(i)) has been commonly used below molybdenum oxide (MoOx) to form a good contact. An a-Si:H(i)/MoOx stack gives good surface passivation, but often results in poor carrier selectivity after exposure to slightly elevated temperatures >130 °C (Geissbühler et al., 2015) [1]. For this reason, we have investigated an alternative interface layer, a very thin Al2O3 tunneling layer (<2 nm), deposited by atomic layer deposition (ALD), that can provide surface passivation, higher transparency and thermal stability without affecting the hole transport across the contact. To demonstrate this new passivating contact a 6" moly-poly cell, with an Al2O3/MoOx stack at the front side and n-type doped polysilicon at the rear side, was made using a high- throughput spatial ALD tool, and E-beam PVD, for the Al2O3 and MoOx layers, respectively. This resulted in an efficiency of 18.2% with a Voc of 651 mV, a FF of 75.6% and a Jsc of 36.9 mA/cm2. A post-deposition anneal (PDA) of the thin Al2O3 interlayer has significant effect on the Al2O3 thickness, layer stoichiometry, contact selectivity, and sputtering-induced damage. Annealing at higher TPDA (350–600 °C) results in ineffective hole carrier transport and makes the stack more sensitive to ITO damage. The best performing device was, therefore, made using an Al2O3 layer without a PDA treatment. Moreover, we have found that this solar cell structure is thermally stable up to at least 210 °C, and even slightly improves under annealing which makes this device industrially appealing.

Efficient Hole Transport Layers for Silicon Heterojunction Solar Cells by Surface Plasmonic Modification in MoOx/Au NPs/MoOx Stacks

Enhanced charge extraction in organic solar cells through electron accumulation effects induced by metal nanoparticles

Plasmonic Electrically Functionalized TiO2 for High‐Performance Organic Solar Cells

Au Nanoparticles On Ultrathin Mos2 Sheets For Plasmonic Organic Solar Cells

MoOx Hole Collection Layer for A-Si: H Based Photovoltaic Cells

Molybdenum oxide hole selective transport layer by hot wire oxidation-sublimation deposition for silicon heterojunction solar cells

Plasmonic Ag@Oxide Nanoprisms for Enhanced Performance of Organic Solar Cells

Simulation of High Efficiency Silicon Heterojunction Solar Cells with Molybdenum Oxide Carrier Selective Layer

Greatly enhanced hole collection of MoOx with top sub-10 nm thick silver films for gridless and flexible crystalline silicon heterojunction solar cells

Improved Efficiency of Silicon Nanoholes/Gold Nanoparticles/Organic Hybrid Solar Cells via Localized Surface Plasmon Resonance

Solution-processed Molybdenum Oxide Hole Transport Layer Stabilizes Organic Solar Cells

Highly Efficient Organic/Silicon Hybrid Solar Cells with a MoO3 Capping Layer

Molybdenum-Oxide-Modified PEDOT:PSS as Efficient Hole Transport Layer in Perovskite Solar Cells

Ultrathin MoS2 nanosheets for high-performance photoelectrochemical applications via plasmonic coupling with Au nanocrystals

Tunable Hole Selective Transport by Solution‐processed MoO3‐x Via Doping for p‐Type Crystalline Silicon Solar Cells

Solution-processed and thickness-insensitive hole transport layer for high efficiency organic solar cells

Enhancing performance of heterojunction silicon solar cells through atomic-layer-deposited MoO x hole contact and atomic-layer-deposited AlZnO layer

Embedding Plasmonic Metal into Heterointerface of MOFs-Encapsulated Semiconductor Hollow Architecture for Boosting CO2 Photoreduction

Thermally stable MoOx hole selective contact with Al2O3 interlayer for industrial size silicon solar cells

Construction of a MoOx/MoS2 Heterojunction via the Surface Sulfurization of the Oxide and Its Photocurrent-Switching Characteristics in the Range of the Broadband Light Spectrum