Abstract:Influences of the number of femtosecond laser pulses on micro-drilling quality of tungsten (W) were investigated. In addition, the morphologies of holes, splashes, residual stress on side walls, and microstructures and performance of side walls under different numbers of pulses were compared. Results show that the hole ablated by using a femtosecond laser with a wavelength of 1030 nm, a pulse width of 230 fs, a focused spot diameter of 10 μm, and a power of 5 W was composed of the inverted cone shaped upper part, cylindrical middle part, and fusiform lower part. When the number of pulses is 4 × 10 6 , the obtained hole is 476.2 μm deep and the upper surface diameter, diameter in the middle part, and maximum diameter in the lower part are separately 35.8, 17, and 32 μm, with a diameter to depth ratio of about 13.3. The surface of internal hole walls at the hole mouth is very smooth, without cracks. Typical laser induced periodic surface structures (LIPSSs) are present on the hole walls, with the characteristic size of 400 nm. Lots of residues are found on the bottom of the hole. The different energy densities of the Gaussian-distributed laser beam irradiating the sidewalls of the small holes at different locations and depths resulted in the different microscopic morphologies of the hole walls.The grain sizes in the ablation affected zones do not differ significantly under the three numbers of pulses. This indicates that there was no significant thermal accumulation leading to grain growth during the femtosecond laser ablation processing of W. The divergence angle of splashes is 68.2°. As the distance from the axis of laser beam enlarges, the splashes are successively lots of nano-sized floccules and spherical particles, lots of nano/micron-sized spherical particles, and a few micron-sized spherical particles. The nanoindentation hardnesses near and far from the hole are separately 12.73–13.55 GPa and 15.07–15.71 GPa. The residual tensile stress on the hole wall is several hundred megapascals higher than that in the area far from the hole. The research analyzed the hole forming mechanism of W during femtosecond laser ablation (FLA) combining with experimental phenomena, formed a set of analytical methods for femtosecond laser ablation processing of small holes, and provided reference for FLA of refractory materials.

Study on Hole Wall Morphology and Defects in Burst Mode of Femtosecond Laser Drilling

Topographic Analysis Of Holes Drilled By Ultrahigh Intensity Nanosecond Uv Laser

Experiments of Drilling Micro-Holes on Superalloy with Thermal Barrier Coatings by Using Femtosecond Laser

Experimental research on micro-drilling of refractory material tungsten by multi-pulse femtosecond laser ablation

Development of a Quantitative Method for the Characterization of Hole Quality During Laser Trepan Drilling of High-Temperature Alloy

Computational and Experimental Study on Hole Evolution and Delamination in Laser Drilling of Thermal Barrier Coated Nickel Superalloy

Experimental study of nickel-based superalloy IN792 with femtosecond laser drilling method

Laser Percussion Drilling of High Temperature Alloy and Qualitative/Quantitative Characterization

Surface Ablation Properties and Morphology Evolution of K24 Nickel Based Superalloy with Femtosecond Laser Percussion Drilling

Picosecond laser drilling study of directional solidification Ni3Al-based superalloy

Structural Changes During Femtosecond Laser Percussion Drilling of High-Aspect-ratio Diamond Microholes

An experimental investigation into the defects of laser-drilled holes in thermal barrier coated Inconel 718 superalloys

Size effect of femtosecond laser helical drilling on nickel-based single crystal superalloy

Characteristic of Hole Wall Trepanning by Picosecond Laser in Superalloy

Percussion Drilling of Deep Holes Using Picosecond Ultrashort Pulse Laser in Ni-Based Superalloy Coated with Ceramic Thermal Barrier Coatings

Percussion Drilling on Nickel-Based Alloy with Thermal Barrier Coatings Using Femtosecond Laser

A comparative study on high pulse energy femtosecond laser drilling of high-aspect-ratio holes under different pressure conditions

Optimizing Hole Shape and Improving Surface Quality of Inconel 718 Alloy by High-Temperature Chemical Assisted Laser Processing

Quantitative Study of High-Frequency Fatigue Hole-Edge Stresses in Nickel-Based Single-Crystal Superalloy

Improving the fatigue property of diffusive film cooling holes in nickel-based single crystal superalloy via ultrashort pulse laser drilling coupled with abrasive flow machining