Abstract:Laser drilling is always accompanied by recast layers, micro-cracks, and heat-affected zones, which limit its application in engineering. Due to its unique advantages, such as no heat-affected zones, no residual stresses, and no dependence on the mechanical properties of the materials, electrochemical dissolution has been adopted to remove the laser drilling-induced surface defects. The electrochemical dissolution characteristics and surface evolution of the laser-drilled Ni-based superalloys were studied. The polarization curves and electrochemical impedance spectroscopy (EIS) of the laser-drilled materials and the substrate were measured, indicating that the laser-drilled surface had a smaller corrosion resistance than the original substrate. X-ray photoelectron spectroscopy (XPS) results showed that the laser-drilled surface had a much higher oxygen content than the substrate. Additionally, electric current efficiency curves were obtained to study the anodic dissolution behavior of Ni-based superalloys. An electric current density in the 5–40 A/cm2 range was preferred to enhance the electrochemical dissolution rate. Moreover, the effects of electric current densities and post-processing time on the surface roughness and the recast layer thickness of the laser-processed Ni-based superalloys were investigated using a NaCl and NaNO3 solution electrolyte. The evolution of the surface quality and recast layer thickness were clarified. Furthermore, an anodic dissolution model of the laser-processed surface was established to illustrate the electrochemical post-processing mechanisms. Results revealed that electrochemical dissolution could completely remove the laser drilling-induced surface defects in 20 s using a 12.5 wt.% NaNO3 solution electrolyte and a 40 A/cm2 electric current density. Finally, an electrochemical post-processed surface with surface roughness (Ra) of 1.7 µm and without a recast layer was achieved. Micro holes without recast layers and Ra of 0.69 µm were obtained with high efficiency using laser processing and electrochemical post-processing.

Picosecond laser drilling study of directional solidification Ni3Al-based superalloy

Investigation on the Microstructure and Mechanical Behaviors of a Laser Formed Nb-Ti-Al Alloy

Characteristic of Hole Wall Trepanning by Picosecond Laser in Superalloy

Laser Drilling of Ni-Base Single-Crystal Superalloy through Thermal Barrier Coatings

Unidirectional Crystal Orientation of Dual-Phase Ni3Al-Based Alloy via Laser Irradiation

Percussion Drilling of Deep Holes Using Picosecond Ultrashort Pulse Laser in Ni-Based Superalloy Coated with Ceramic Thermal Barrier Coatings

Laser cladding repairing of directionally solidified nickel base superalloy and its tensile properties

Epitaxial growth behavior and stray grains formation mechanism during laser surface re-melting of directionally solidified nickel-based superalloys

Microstructure and Nanoindentation Creep Behavior of IC10 Directionally Solidified Superalloy Repaired by Laser Metal Deposition

A Study on the Cracking Behaviour in Laser Metal Deposition of IC10 Directionally Solidified Nickel-Based Superalloy

Study on anodic dissolution behavior and surface evolution of laser-drilled Ni-based superalloys during electrochemical post-processing

Effects of Recast Layer on Fatigue Performance of Laser-Drilled Holes in Nickel-Based Superalloy

Experimental study of nickel-based superalloy IN792 with femtosecond laser drilling method

Mechanisms of femtosecond laser ablation of Ni3Al: Molecular dynamics study

Microstructural Investigations of Ni-Based Superalloys by Directional Solidification Quenching Technique

Hot cracking behavior and mechanism of the IC10 directionally solidified superalloy during laser re-melting

Design of a novel crack-free precipitation-strengthened nickel-based superalloy and composites for laser powder bed fusion

Characterization of the Recasting-Affected Zone in the Nickel-Based Superalloy Upon Single-Pulse Laser Treatment

Multi-scale microstructural investigation of a laser 3D printed Ni-based superalloy

Origin of hot cracking formation and suppression method in laser additive manufactured nickel-based superalloys

Boundary Liquation and Interface Cracking Characterization in Laser Deposition of Inconel 738 on Directionally Solidified Ni-based Superalloy