Abstract:The paper investigates the characteristics of the laser beam percussion micro-drilling (LBPMD) process in aerospace nickel-based superalloy Hastelloy X using microsecond pulses. The quality of the drilled hole is crucial in laser beam micromachining, and selecting appropriate process parameters significantly impacts the hole's quality. The objective is to achieve predefined hole dimensions with minimal taper angles. Additionally, the study focuses on the alteration of pulse width, which is a combination of laser pulse frequency and duty cycle. Laser power ( P ), duty cycle % ( D ), focal plane position ( FPP ), and laser frequency ( f ) are considered input parameters, while geometric features such as inlet and outlet diameters, hole taper angle, and inlet circularity are examined as process responses. ANOVA is employed to establish significant relationships between process parameters and response variations based on experimental tests. Creating a precise simulation model that accurately accounts for the moving boundary of the target material's receding surface is a crucial and challenging task in formulating the laser heat conduction problem. It is necessary to simultaneously capture the material's dynamic front movement and update the boundary conditions of the laser source. To model the micro-drilled hole with LBPMD, the UMESHMOTION and DFLUX subroutines, along with the arbitrary Lagrangian-Eulerian (ALE) adaptive remesh algorithm in the AbaqusTM software, are utilized. Notably, no previous numerical study has predicted the geometry of micro-drilled holes using this technique. The proposed procedure is validated through the predictions of inlet and outlet hole diameters. Special emphasis is placed on the validation of models. Consequently, the numerical model and statistical model are compared as well as the need to define model applicability. The study demonstrates that all input parameters significantly influence the inlet hole diameter, while the pulse width notably affects the taper angle and circularity. The interaction between high laser frequency and low duty cycle results in reduced pulse duration. Multi-objective optimization is performed to determine the optimal process parameter settings for desired quality characteristics, considering minimum hole taper angle, precise inlet diameter, and maximum inlet circularity of the hole as optimization criteria. The findings show that with the optimized predicted results obtained from the optimal input variables, a composite desirability of 92% can be achieved.

Laser Percussion Drilling of High Temperature Alloy and Qualitative/Quantitative Characterization

Development of a Quantitative Method for the Characterization of Hole Quality During Laser Trepan Drilling of High-Temperature Alloy

Percussion Drilling of Deep Holes Using Picosecond Ultrashort Pulse Laser in Ni-Based Superalloy Coated with Ceramic Thermal Barrier Coatings

An experimental investigation into the defects of laser-drilled holes in thermal barrier coated Inconel 718 superalloys

Comparison of percussion laser drilling quality with and without water-based ultrasonic assistance

Optimizing Hole Shape and Improving Surface Quality of Inconel 718 Alloy by High-Temperature Chemical Assisted Laser Processing

Study of the TBC delamination in nanosecond laser percussion drilling of inclined film cooling holes

A novel numerical modeling of microsecond laser beam percussion micro-drilling of Hastelloy X: experimental validation and multi-objective optimization

Experimental Characterization of Laser Trepanned Microholes in Superalloy GH4220 with Water-Based Assistance

A comprehensive study on water jet guided laser micro hole drilling of an aerospace alloy

Optimization of Femtosecond Laser Drilling Process for DD6 Single Crystal Alloy

Effect of water-based ultrasonic vibration on the quality of laser trepanned microholes in nickel super-alloy workpieces

Laser drilling of micro-holes with controllable taper using 355 nm nanosecond laser

Experimental Investigation on the Spiral Trepanning of K24 Superalloy with Femtosecond Laser

Picosecond laser drilling study of directional solidification Ni3Al-based superalloy

Trepanning of Supper-Alloy with Thermal Barrier Coating Using Femtosecond Laser

Investigation on Thermal Barrier Coating Damages for Ultrafast Laser Drilling of Cooling Holes

Molecular dynamics-guided quality improvement in the femtosecond laser percussion drilling of microholes using a two-stage pulse energy process

An investigation on the hole quality during picosecond laser helical drilling of stainless steel 304

Analysis of the Effects of Water Temperature on Water-Assisted Laser Trepanning in Superalloys

Surface integrity of drilling Ti-6Al-4V micro-holes using the ultrashort pulse laser with different three-dimensional paths planning