Abstract:Laser drilling is always accompanied by recast layers, micro-cracks, and heat-affected zones, which limit its application in engineering. Due to its unique advantages, such as no heat-affected zones, no residual stresses, and no dependence on the mechanical properties of the materials, electrochemical dissolution has been adopted to remove the laser drilling-induced surface defects. The electrochemical dissolution characteristics and surface evolution of the laser-drilled Ni-based superalloys were studied. The polarization curves and electrochemical impedance spectroscopy (EIS) of the laser-drilled materials and the substrate were measured, indicating that the laser-drilled surface had a smaller corrosion resistance than the original substrate. X-ray photoelectron spectroscopy (XPS) results showed that the laser-drilled surface had a much higher oxygen content than the substrate. Additionally, electric current efficiency curves were obtained to study the anodic dissolution behavior of Ni-based superalloys. An electric current density in the 5–40 A/cm2 range was preferred to enhance the electrochemical dissolution rate. Moreover, the effects of electric current densities and post-processing time on the surface roughness and the recast layer thickness of the laser-processed Ni-based superalloys were investigated using a NaCl and NaNO3 solution electrolyte. The evolution of the surface quality and recast layer thickness were clarified. Furthermore, an anodic dissolution model of the laser-processed surface was established to illustrate the electrochemical post-processing mechanisms. Results revealed that electrochemical dissolution could completely remove the laser drilling-induced surface defects in 20 s using a 12.5 wt.% NaNO3 solution electrolyte and a 40 A/cm2 electric current density. Finally, an electrochemical post-processed surface with surface roughness (Ra) of 1.7 µm and without a recast layer was achieved. Micro holes without recast layers and Ra of 0.69 µm were obtained with high efficiency using laser processing and electrochemical post-processing.

Improving the fatigue property of diffusive film cooling holes in nickel-based single crystal superalloy via ultrashort pulse laser drilling coupled with abrasive flow machining

Quantitative Study of High-Frequency Fatigue Hole-Edge Stresses in Nickel-Based Single-Crystal Superalloy

Fatigue performance improvement of laser shock peened hole on powder metallurgy Ni-based superalloy labyrinth disc

High-Cycle Fatigue Fracture Behavior and Stress Prediction of Ni-Based Single-Crystal Superalloy with Film Cooling Hole Drilled Using Femtosecond Laser

Effects of Recast Layer on Fatigue Performance of Laser-Drilled Holes in Nickel-Based Superalloy

High-temperature fatigue life improvement of small-deep holes by using a novel cold expansion process in a nickel-based superalloy

Experimental validation of residual stress thermomechanical simulation in as-quenched superalloy discs by using diffraction and incremental hole-drilling methods

Optimizing Hole Shape and Improving Surface Quality of Inconel 718 Alloy by High-Temperature Chemical Assisted Laser Processing

Experimental study of nickel-based superalloy IN792 with femtosecond laser drilling method

Femtosecond laser high-quality drilling of film cooling holes in nickel-based single superalloy for turbine blades with a two-step helical drilling method

A novel cold expansion process for improving the surface integrity and fatigue life of small-deep holes in Inconel 718 superalloys

Research on low‐cycle fatigue behavior of Ni‐based single crystal superalloy with shaped film cooling holes at high temperature

Temperature-Stress Coupling Fatigue Behavior of Film-Cooling Holes in Complex Temperature Fields

Laser Surface Remelting in Single-Crystal Nickel-based Superalloy using a Continuous Wave Fiber Laser

Fatigue Life Prediction of Film-cooling Hole Specimens with Initial Damage

Size effect of femtosecond laser helical drilling on nickel-based single crystal superalloy

Improvement of wetting and necking of nickel-based superalloys fabricated by sequential dual-laser powder bed fusion via particle-scale computational fluid dynamics

Evaluation of different drilling quality and fatigue life prediction of nickel-based superalloy using equivalent initial flaw size

Grinding surface and subsurface stress load of nickel-based single crystal superalloy DD5

Study on anodic dissolution behavior and surface evolution of laser-drilled Ni-based superalloys during electrochemical post-processing

Improving fatigue properties of normal direction ultrasonic vibration assisted face grinding Inconel 718 by regulating machined surface integrity