Abstract:This paper presents characterization and compensation of the thermal bias drift of a MEMS accelerometer whose effective stiffness is electrostatically tuned to a low value with the help of the single-sided parallel plates (SSPPs) capacitors. A temperature drift model for the proposed accelerometer is built and the temperature effect on the mechanical stiffness and the circuit gains is characterized. The characterization reveals that the variations of the feedforward coefficient including the mechanical stiffness and the readout gain due to the temperature change play a significant role in the bias drift of output of the proposed closed-loop accelerometer. On the other hand, the variations of both feedback gain and tuning gain as a function of temperature are one-order-of-magnitude less than that of the feedforward coefficient. To calibrate the feedforward coefficient, an excitation signal as a form of AC reference displacement is introduced to drive the proof mass and the readout response is demodulated to calibrate the variance of the feedforward coefficient correspondingly. An open-loop compensation scheme for the temperature-induced bias drift using the variance of the calibrated response is proposed accordingly. Alternatively, the calibrated response can be controlled to a preset value by a new proportion integral derivative (PID) controller by the adjustment of the SSPP tuning voltage. The output of the PID controller is used for the calibration of the introduced bias from the electrostatic tuning force. Therefore, a closed-loop compensation of the thermal bias drift is achieved by remaining the feedforward coefficient while eliminating the calibrated bias. Experiments under a temperature cooling process and different tuning voltages are carried out to verify two proposed compensation schemes. The temperature drift coefficients (TDCs) of both compensated outputs exhibit at least one-order-of-magnitude reduction in response to the temperature change. When the effective stiffness of the accelerometer is tuned to about 4.19 N m(-1), the TDC of the compensated output using the proposed open-loop or closed-loop compensation schemes is reduced to about 0.1136 or 0.0391 mg degrees C-1, respectively and meanwhile, the Allan bias instability is slightly increased to 48.63 or 56.14 mu g, respectively.

Stiffness Imbalance Errors Trimming for Silicon Mems Tuning-Fork Gyroscopes with Low Cost Picosecond Lasers

A MICROMECHANICAL MODE-MATCHED GYROSCOPE USING STIFFNESS NONLINEARITY AND ELECTROSTATIC TUNING

A Stiffness-Tunable MEMS Accelerometer

Identification and Suppression of Driving Force Misalignment Angle for a MEMS Gyroscope Using Parametric Excitation

Trimming method for MEMS gyroscope by femtosecond laser

A Novel Mechanical Frequency Tuning Method Based on Mass-Stiffness Decoupling for MEMS Gyroscopes

A 0.09°/h Bias-Instability MEMS Gyroscope Working with a Fixed Resonance Frequency

Linear stiffness tuning of MEMS triangular capacitors

A Sub-0.1°/H Bias-Instability MEMS Gyroscope Using Resonant Constant-Frequency Driving Technique

A Digital Control Structure for Lissajous Frequency-Modulated Mode MEMS Gyroscope

Reduction of High-Frequency Laser Noise in Resonant Fiber Optic Gyroscope with a Phase-Modulated Feedback Loop

Characterization and Compensation of Thermal Bias Drift of a Stiffness-Tunable MEMS Accelerometer

Automatic Pico Laser Trimming System for Silicon MEMS Resonant Devices Based on Image Recognition

A Low-Complexity In-Run Modal Frequency Tuning Method for MEMS Disk Gyroscopes Without Gain Calibration and Phase Shifting

A trimming method for MEMS gyroscopes by focused ion beam etching

Research on Laser Trimming of Silicon Mems Vibratory Gyroscopes

Interactive Errors Analysis and Scale Factor Nonlinearity Reduction Methods for Lissajous Frequency Modulated MEMS Gyroscope

Vibration Sensitivity Reduction of Micromachined Tuning Fork Gyroscopes through Stiffness Match Method with Negative Electrostatic Spring Effect

Initial Frequency Split Reduction of MEMS Ring Gyroscope Based on Cascaded Springs Geometrical Compensation

Research on the Mass Adding and Removing Combined Mechanical Trimming Method of the Ring MEMS Gyroscope

Bandwidth optimization design of a multi degree of freedom MEMS gyroscope