Abstract:One of challenges in improving the performance and cost‐effectiveness of SOFCs (solid oxide fuel cells) is the development of suitable interconnects materials. Chromia‐forming alloys and especially ferritic stainless steels, like Crofer22APU, are considered to be among the most promising candidate materials as interconnects in SOFC stacks. However, the performance of chromia‐forming materials can be limited by the low electronic conductivity of the oxide scale (high ASR – area specific resistance – value). Such degradation are unacceptable regarding the long‐term operation (>40 000 h). A previous study 1 demonstrated that in air, the addition of a nanometric reactive element oxide (La2O3) layer applied by metal organic chemical vapor deposition (MOCVD) drastically improved both corrosion rate and electrical properties of Crofer22APU and Haynes230 alloys for 100 h at 800 °C. In this present study coating performances were checked after 10 months (7500 h) and 20 months (15 000 h) at 800 °C in air. The corrosion products were carefully analyzed by SEM, EDX, and XRD. ASR measurements are realized after long time exposure. This study demonstrates that the Crofer22APU alloy has a good oxidation resistance after 15 000 h in air but this alloy has an ASR value equal to 0.370 Ω cm2. The coatings composed of a thin reactive element oxide such as La2O3 resulted in an important improvement in the high temperature oxidation resistance; the ASR values are equal to 0.154 Ω cm2. Haynes230 alloy has a better oxidation resistance but the formation of an insulating Al2O3/SiO2 layer could be detrimental.

Microstructure Evolution of Magnetron Sputtered Ce-Based Coatings for Solid Oxide Fuel Cell Interconnector: under the Anode Operating Environment

Metallic Co with Reactive Element Oxide Composite Coatings for Solid Oxide Fuel Cell Interconnect Applications

Investigation of Thin Coatings from Mn-Co-Fe System Deposited by PVD on Metallic Interconnects for SOFC Applications

Anode Performance of Mn-doped Ceria–scsz for Solid Oxide Fuel Cell

Effect of MnCoNiFeCu Alloy on Oxidation Behavior and Electrical Performance of AISI 441 for SOFC Interconnect Application

Oxidation and electrical properties of nanostructured CeO 2 –Ni coating on solid oxide fuel cell interconnects

Co-Sintering of Spinel-Based Coating/Contact Dual-Layer Structure for Solid Oxide Fuel Cell Cathode-Side Application

Efficient FeCoNi/CeO 2 coatings for solid oxide fuel cell steel interconnect applications

Characterization of La0.8Sr0.2Co0.5Mn0.5O3-δ Coating on Alloy Interconnect in SOFC

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Mechanical reliability and life prediction of coated metallic interconnects within solid oxide fuel cells

Metallic interconnects for solid oxide fuel cell: Performance of reactive element oxide coating during long time exposure

Metallic Interconnects for Solid Oxide Fuel Cell: Performance of Reactive Element Oxide Coating During 10, 20 and 30 Months Exposure

Evaluation of Protective La0.67Sr0.33MnO3–δ Coatings on Various Stainless Steels Used for Solid Oxide Fuel Cell Interconnects

Studies on Composite Cathode with Nanostructured Ce0.9Sm0.1O1.95 for Intermediate Temperature Solid Oxide Fuel Cells

Enhancement in surface exchange coefficient and electrochemical performance of Sr2Fe1.5Mo0.5O6 electrodes by Ce0.8Sm0.2O1.9 nanoparticles

Protective coatings for Cr2O3-forming interconnects of solid oxide fuel cells

The Preparation and Properties of Ti(Nb)-Si-C Coating on the Pre-Oxidized Ferritic Stainless Steel for Solid Oxide Fuel Cell Interconnect

Oxidation Behavior of Ferritic Stainless Steel Interconnect Coated by a Simple Diffusion Bonded Cobalt Protective Layer for Solid Oxide Fuel Cells

Mechanical characterization of oxide coating–interconnect interfaces for solid oxide fuel cells

Investigation into the diffusion and oxidation behavior of the interface between a plasma-sprayed anode and a porous steel support for solid oxide fuel cells