Abstract:The performance of solid oxide electrolyzer cells (SOEC) can be improved through the development of coatings applied to the surface of ferritic steel interconnects in view of mitigating chromium evaporation and reducing the growth rate of low conductive oxides in oxidizing environments. This work investigated the oxidation and area specific resistance (ASR) of two electrodeposited nickel coatings on preoxidized and non-preoxidized AISI 441 ferritic stainless steel substrates. The nickel coating effectively restricted the outward diffusion of chromium after 100 h of exposure at 700 °C in air but led to nickel/iron interdiffusion between the substrate and coating forming an iron-nickel-rich spinel on the surface, with NiO underneath and Cr 2 O 3 at the coating-substrate interface and at the coating grain boundaries. The application of a LSM ((La 0.80 Sr 0.20 ) 0.95 MnO 3−x ) coating on top of the Ni electrodeposited coatings resulted in the same type of oxides but the oxidation kinetics were slower. Interdiffusion continued with the exposure at 700 °C for 2400 h resulting in the growth of a thick iron-rich oxide layer on top of Cr 2 O 3 , steadily raising the interconnect ASR to 25 mΩ cm 2 . The addition of a preoxidation step before the electrodeposit of nickel helped to limit iron-nickel interdiffusion, leading to the formation of a thicker NiO layer on a Cr 2 O 3 layer between substrate and coating. While the ASR was higher than without preoxidation at the beginning of the test, it stabilized at about 33 mΩ cm 2 after 1750 h. Despite displaying a higher electrical resistance, the coatings effectively limited the outward chromium diffusion throughout exposure compared to the bare substrate.

Oxidation and electrical properties of nanostructured CeO 2 –Ni coating on solid oxide fuel cell interconnects

Efficient FeCoNi/CeO 2 coatings for solid oxide fuel cell steel interconnect applications

Metallic Co with Reactive Element Oxide Composite Coatings for Solid Oxide Fuel Cell Interconnect Applications

Oxidation and electrical behavior of Ni-Mn3O4-La2O3-coated SOFC interconnect steel

A Promising NiCo2O4 Protective Coating for Metallic Interconnects of Solid Oxide Fuel Cells

Effect of Cu on the diffusion behavior and electrical properties of Ni-Co conversion coating for metallic interconnects in solid oxide fuel cells

The Preparation and Properties of Ti(Nb)-Si-C Coating on the Pre-Oxidized Ferritic Stainless Steel for Solid Oxide Fuel Cell Interconnect

Microstructure and diffusion behavior of Co-Ni-W conversion coating for metallic interconnect of solid oxide fuel cell

Fe doped Ni–Co alloy by electroplating as protective coating for solid oxide fuel cell interconnect application

Protective coatings for Cr2O3-forming interconnects of solid oxide fuel cells

A Highly Coking-Resistant Solid Oxide Fuel Cell with a Nickel Doped Ceria: Ce1−xNixO2−y Reformation Layer

Microstructure Evolution of Magnetron Sputtered Ce-Based Coatings for Solid Oxide Fuel Cell Interconnector: under the Anode Operating Environment

Cufe2o4 Nano-Spherical Powder Directly Served As Interconnect Coating for Solid Oxide Fuel Cells Applications

CeO2 coated NaFeO2 proton-conducting electrolyte for solid oxide fuel cell

CrxN/Mn1.7Cu1.3 coating on ferritic stainless steel for solid oxide fuel cell interconnects

Oxidation Behavior and Electrical Property of A Ni-Based Alloy in Sofc Anode Environment

Cu-Fe spinel coating as oxidation barrier for Fe-16Cr metallic interconnect in solid oxide fuel cells

Oxidation Behavior of Ferritic Stainless Steel Interconnect Coated by a Simple Diffusion Bonded Cobalt Protective Layer for Solid Oxide Fuel Cells

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Impact of nickel on the surface reaction in ceria-based electrodes for solid oxide cells

Effect of Electrodeposited Nickel Coatings on the High Temperature Degradation and Electrical Performance of Steel SOEC Interconnects