Abstract:Research highlights•High-entropy transition metal carbides with regulatable carbon stoichiometry (HE TMCx) achieve the promoting of formation ability from carbon stoichiometry deviations.•Bulk (Zr0.25Hf0.25Ta0.25Nb0.25)Cx (SPS-ZHTNCx) with carbon stoichiometry deviations show promoted sintering.•Bulk (Zr0.25Hf0.25Ta0.25Nb0.25)Cx (SPS-ZHTNCx) present tunable mechanical properties.Tremendous efforts have been dedicated to promote the formation ability of high-entropy transition metal carbides. However, the majority of methods for the synthesis of high-entropy transition metal carbides still face the challenges of high temperature, low efficiency, additional longtime post-treatment and uncontrollable properties. To cope with these challenges, high-entropy transition metal carbides with regulatable carbon stoichiometry (HE TMCx) were designed and synthesized, achieving improved ability for single phase solid solutions formation, promoting of sintering and controllable mechanical properties. Two typical composition series, i.e., easily synthesized (Zr0.25Hf0.25Ta0.25Nb0.25)C (ZHTNC) and difficultly synthesized (Zr0.25Hf0.25Ta0.25Ti0.25)C (ZHTTC) are selected to demonstrate the promoting formation ability of single phase solid solutions from carbon stoichiometry deviations. Single phase high-entropy ZHTTC, which has been proven difficult in forming a single phase solid solution, can be prepared with the decrease of C/TM ratio under 2000°C; while the high-entropy ZHTNC, which has been proven easy in forming a single phase solid solution, can be synthesized at lower temperatures with the decrease of C/TM ratio. The synergistic effect of entropy stabilization and reduced chemical bond strength gaining from carbon stoichiometry deviations is responsible for the formation of single phase solid solutions and the promoted sintering of HE TMCx. For example, the relative density of bulk (Zr0.25Hf0.25Ta0.25Nb0.25)Cx (SPS-ZHTNCx) increases from 90.98% to 94.25% with decreasing the C/TM atomic ratio from 0.9 to 0.74. More importantly, the room temperature flexural strength, fracture toughness and brittleness index of SPS-ZHTNCx can be tuned in the range of 384 MPa–419 MPa, 4.41 MPa m1/2–4.73 MPa m1/2 and 3.679 μm−1/2–4.083 μm−1/2, respectively. Thus, the HE TMCx prepared by adjusting the ratio of carbon to refractory transition metal oxides have great potential for achieving low temperature synthesis, promoted sintering and tunable properties.

Carbon Vacancies Enhanced Oxidation Resistance of High-Entropy Carbides (ti0.2v0.2nb0.2mo0.2w0. 2)Cx

Ordered C vacancies in titanium carbides: a correlation between crystal structure and the effects on oxidation behavior at elevated temperature

The significant influence of carbon content on mechanical and thermal properties of (VNbTaMoW)0.5Cx high entropy carbides

Mechanisms responsible for enhancing low‐temperature oxidation resistance of nonstoichiometric (Zr,Ti)C

A practical guideline for designing high-entropy carbides based on (Ti1/3Mo1/3W1/3)C with high valence electron concentration

Carbon vacancies regulation strategy for boosting the high-temperature microwave absorption performance of (Co0.2Mo0.2V0.2Nb0.2Ta0.2)Cx high-entropy carbides

Effect of carbon content on the microstructure and mechanical properties of high-entropy (Ti0.2Zr0.2Nb0.2Ta0.2Mo0.2)Cx ceramics

Mechanical and tribological performance of (TiNbTaWMo)C high-entropy ceramics in a wide temperature range

Compositional optimization for enhanced oxidation resistance of high-entropy carbide ceramics

Oxidation behavior of non-stoichiometric (Zr,Hf,Ti)Cx carbide solid solution powders in air

Oxidation behavior of (NbTaZrW)C high-entropy carbide at 800–1000 °C

Mechanical Properties of High-Entropy Carbides Prepared by High-Pressure Sintering: Role of Carbon Stoichiometry

Effect of (Ti,W)C/TaC addition on the early oxidation behavior of surface layer of WC-Co cemented carbides

A promising new class of high-entropy ceramics: High-entropy oxycarbides with good oxidation resistance

Effect of Ti and C addition on oxidation resistance of FeCoCrNiMn high entropy alloys prepared by powder metallurgy

Regulating the formation ability and mechanical properties of high-entropy transition metal carbides by carbon stoichiometry

Non-stoichiometry of (TiZrHfVNbTa)C x and its significance to the microstructure and mechanical properties

Influence of vanadium content on the microstructural evolution and mechanical properties of (TiZrHfVNbTa)C high-entropy carbides processed by pressureless sintering

Tuning structure, mechanical properties, and oxidation resistance of (Nb, Ta)C1- solid solution powders via the dissolution-precipitation process

Effects of boron and carbon on the oxidation behavior of a NbMoTaW refractory high entropy alloy

Effect of Y2O3 Addition on High-Temperature Oxidation of Binderless Tungsten Carbide