Abstract:To meet the practical application, a kind of commercially available Si3N4 powder by direct Si nitridation was used to fabricate dense Si3N4/SiC nanocomposite by pressureless sintering method. The price of this kind of powder is much lower than that of powder by imide decomposition. 5-30 vol% of SiC powder (average particle size: 80 nm) were added in the composite to investigate the effect of SiC particle. Totally 15 wt% of MgAl2O4 and ZrO2 (50 wt% each) were used as sihtering additives. With increasing SiC content, the densities of the composites decreased. α-β Si3N4 phase transformation was enhanced at low temperatures, but prohibited at high temperatures for large SiC content. The sample with larger SiC content gave a relatively smaller Si3N4 grain size because SiC particles limit the Si3N4 grain growth by pinning and prohibiting the grain boundary movement. An improvement of Young's modulus, flexural strength and hardness by the SiC addition was found. Further increase in SiC content resulted in a decrease of these properties because of the decreasing density for the samples sintered at low temperatures. With an intermediate sintering temperature, the samples with 20 vol% SiC reached to high flexural strength as 1050 MPa as a result of good density and relatively fine grain size structure. The decreased fracture toughness with increasing the SiC content was observed by the refinement of Si3N4 grain. However, it was improved with the increasing sintering temperature. The result of this study provided an economic way to fabricate the Si3N4/SiC nanocomposite with a strength higher than 1 GPa and appropriate fracture toughness.

Spheroid Growth During Sintering of Copper Coated Silicon Carbide Particles in the Fabrication of Nanocomposite

Refining Micron-Sized Grains to Nanoscale in Ni-Co Based Superalloy by Quasistatical Compressive Deformation at High Temperature

Effect of Cu2O on the Fabrication of SiCp/Cu Nanocomposites Using Coated Particles and Conventional Sintering

Sintering Densification of Cu/Al2O3p Nano-Composite Powders by Electroless Copper Plating

Grain Growth and Recrystallization Behaviors of an Ultrafine Grained Al-0.6 Wt%mg-0.4 Wt%si-5Vol.%sic Nanocomposite During Heat Treatment and Extrusion

Thermodynamic Behavior of Copper-Coated Silicon Carbide Particles during Conventional Heating and Spark Plasma Sintering

The microstructure and deformation behavior of W-SiC composites via spark plasma sintering

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Preparation and characterization of coated nanoscale Cu/SiCp composite particles

Fabrication of Ni/Sic Composite Powder by Mechanical Alloying and Its Effects on Properties of Copper Matrix Composites

Investigation of SiC Nanoparticle Size and Distribution Effects on Microstructure and Mechanical Properties of Al/SiC/Cu Composite during the FSSW Process: Experimental and Simulation

In situ investigation of the silicon carbide particles sintering

Carbide assisted in-suit growth and formation mechanism of SiC nanowires on the surface of defined carbon fibers

Effect of Cu Particles on Phase Transformation of Spark Plasma Sintered Silicon Nitride

Fabrication and Characterization of Sic Rod-Particulate-Reinforced Reaction-Bonded Si3n4 Composites

Influence of Conductive Nano-Tic on Microstructural Evolution of Si3n4-Based Nanocomposites in Spark Plasma Sintering

Silicon carbide particle size effects in Al2O3-SiC nanocomposites

Processing and Characterization of SiB0.5C1.5N0.5 Produced by Mechanical Alloying and Subsequent Spark Plasma Sintering

Carbothermally prepared nanophase SiC/ Si3N4 composite powders and densified parts

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Superplasticity and sinter-forging of fine-grained Si3N 4-Si2N2O composite