Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

Effect of Cu2O on the Fabrication of SiCp/Cu Nanocomposites Using Coated Particles and Conventional Sintering

Influence Of Cu2o On Interface Behavior Of Copper/Sicp Composite Prepared By Spark Plasma Sintering

Influence of impurities on the sintering densification in nano- Al2O3 powders coated by copper

Preparation and characterization of coated nanoscale Cu/SiCp composite particles

Sintering Densification of Cu/Al2O3p Nano-Composite Powders by Electroless Copper Plating

Spheroid Growth During Sintering of Copper Coated Silicon Carbide Particles in the Fabrication of Nanocomposite

Fabrication of Ni/Sic Composite Powder by Mechanical Alloying and Its Effects on Properties of Copper Matrix Composites

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Thermophysical, Thermochemical Behavior of Cu Coated Sic Composite Particles

Temperature-sensitivity of coating copper on sub-micron silicon carbide particles by electroless deposition in a rotation flask

Effect of Al2O3 addition on the microstructure and oxidation behavior of SiC coating prepared by pack cementation on C/C composites

Effect of Α-Al2o3 Coatings on the Interface of Ni/SiC Composites Prepared by Electrodeposition

Microstructure and thermal properties of SiCp/Cu composites with Mo coating on SiC particles

Analysis on the phase distribution of nano SiC particles coated with Cu

Development of Cu -Based Composites Reinforced by Particles

Effect of Cu Particles on Phase Transformation of Spark Plasma Sintered Silicon Nitride

Effects of Gd element and SiC particles on microstructures of Cf/Mg composites

Novel coassembly route to Cu-SiO2 MCM-41-like mesoporous materials.

Thermodynamic Behavior of Copper-Coated Silicon Carbide Particles during Conventional Heating and Spark Plasma Sintering

Effect of sintering temperature on fine-grained Cu W composites with high copper

Study on Preparation of Cu2O-Cu Composites