Abstract:As a result of increasing energy demands and accelerated environmental problems, there is an urgent need to improve the thermal efficiency of ultra supercritical (USC) power plants. To achieve this goal, advanced ultra-supercritical (A-USC) technologies with the main steam temperature of 700 similar to 750 degrees C and pressure of 35 MPa have been developed quickly in recent years. One of the most promising candidate Ni-based superalloys for the main steam pipe of 700 degrees C ultra-supercritical coal-fired power plants is Inconel 740H, which is a modified version of Inconel 740 developed by Special Metals Corp (SMC). Compared with IN740, the Ti/Al ratio in IN740H is lowered in order to stabilise the microstructure at long ageing times. In addition, the Nb content is lowered to improve the weldability. In this work, the microstructure evolutions, the nucleation and propagation mechanisms of microcracks in the nickel base superalloy Inconel 740H at 750 degrees C high temperature were studied by the self-developed in situ high temperature tensile stage inside a SEM. The results showed that under the uniaxial tensile stress at 22 degrees C room temperature and 750 degrees C high temperature conditions, the grain boundaries of Inconel 740H alloy are al-ways the most primary crack sources. The strength of grain boundaries is higher than that of grains under the room temperature, and the microcracks will be nucleated at the grains as well, but the relative strength of grain boundaries will be weaken under the high temperature, which makes the microcracks tend to nucleate at grain boundaries. The experimental results also showed that the influence of high temperature on the mechanical properties is very significant, the high temperature reducing the activate energy of slip and weakening the strength of the grain boundaries, so that more slip systems activated and the grain boundaries occurring bending and sliding deformation, so further enhance the ability of plastic deformation of alloy. However, the reduction of relative strength of alloy grain boundaries leads to microcracks nucleation and propagation more easily from grain boundaries and lower the yield strength and tensile strength of alloy.

The Application of Grain Boundary Engineering to a Nickel Base Superalloy for 973 K (700 °C) USC Power Plants

Improve the ductility of a nickel based superalloy by optimizing secondary phase distribution through grain boundary engineering

Grain Boundary Engineering of a Low Stacking Fault Energy Ni-based Superalloy

Creep Behavior and Deformation Mechanism of a Third-Generation Single Crystal Ni-Based Superalloy at 980 °C

Microcrack Nucleation and Propagation Investigation of Inconel 740H Alloy under in Situ High Temperature Tensile Test

Microstructure evolution of a nickel‐based powder metallurgy superalloy under different solution treatment temperatures

Precipitation and Evolution of Grain Boundary Boride in A Nickel-Based Superalloy During Thermal Exposure

New insights into ductility improvement of a nickel-based superalloy through grain boundary engineering

Heat Treatment of a Candidate Material for 700 °C A-USC Power Plants

Comparative study of high-temperature grain boundary engineering of two powder-processed low stacking-fault energy Ni-base superalloys

Investigation of Precipitation Behavior of a Novel Ni-Fe-Based Superalloy during High-Temperature Aging Treatment

Evolution of grain boundary character distribution in near-surface regions of a cold-rolled nickel-based superalloy during induction heating process

Computational approach to grain boundary segregation engineering of nickel-base superalloys

Grain boundary network evolution in electron-beam powder bed fusion nickel-based superalloy Inconel 738

Microstructures and homogenization behavior of a nickel-based superalloy used for 850¬Ý‚ÑÉ turbine disc prepared by electron beam smelting layered solidification

Microstructure and deformation mechanism of Ni-based wrought superalloys for A-USC power plants: a review

An innovative approach towards forming the serrated grain boundaries and refining the γ′ precipitates in nickel-based superalloys

The Effects of Grain Size and Twins Density on High Temperature Oxidation Behavior of Nickel-Based Superalloy GH738

Eliminating embrittlement of GH4065A superalloy at intermediate temperature by a novel grain boundary strengthening mechanism

Processing, Microstructures and Mechanical Properties of a Ni-Based Single Crystal Superalloy

Hot deformation behavior and microstructure evolution of a novel nickel-based powder metallurgy superalloy