Abstract:The Ni-Fe-based superalloy GH4169 (Inconel718) is widely used for several critical gas-turbine components which are hot forged. Its microstructure and property are sensitive to the parameter adjustment during hot working process. To obtain required low-cycle fatigue and fracture properties, it is essential that the microstructure is controlled during preheating and heat treatment. The evolution of non-uniform microstructure during hot working is more complicated than that of uniform microstructure. On the other hand, various secondary phases can be observed in GH4169 alloy, thus it is important to investigate the effect of secondary phases on the microstructure evolution during forging process. In this work, the mechanisms of non-uniform microstructure evolution in GH4169 alloy were studied by analyzing the evolution of secondary phases, grain boundary misorientation, grain size and interactions of dislocation. It is found that the volume fraction of 8 phase increases with the increasing of temperature and heating time at the lower temperature. While at the higher temperature, it decreases monotonously with the temperature increasing, but increases first and then decreases to stable value with time increasing. The pinning effect of secondary phases in GH4169 alloy can be concluded that the gamma '' phase and 8 phase precipitated within the grains retain movement of dislocation, the 8 phase precipitated at the grain boundary hinders the nucleation and growth of recrystallized grains, and the carbides limits the grain growth. The frequency of low angle grain boundary decreases with temperature and time increasing, and the mobility of low angle grain boundary increases with temperature increasing. The uniformity of microstructure and the size of equaxied subgrain increases with heating temperature and time increasing. Continuous recrystallization of elongated grain occurs at specific conditions. The mechanisms of non-uniform microstructure evolution during heating process can be concluded as sub grain growth, recrystallized grain growth, and anneal twinning nucleation and growth. The recrystallized grains are formed by the growth of subgrains conducted by the rotation of low angle grain boundary and the movement of dislocation. When the grain growth is pinned, the mechanisms for the energy dissipation is the nucleation and growth of anneal twinning. And the growth of anneal twinning promotes the generation of low angle grain boundaries at the tip of partial anneal twinning.

Eliminating embrittlement of GH4065A superalloy at intermediate temperature by a novel grain boundary strengthening mechanism

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Thermal Stability of GH4065A Superalloy Based on Microstructural and Performance Evolution Following Long-Term Aging

Mechanisms of Non-Uniform Microstructure Evolution in Gh4169 Alloy During Heating Process

Preparing Gradient Microstructure to Achieve Enhanced Performance in GH4586 Superalloy: Experiments and Models

Microstructure and mechanical properties of a new Ni–Co based superalloy at intermediate temperatures

Achieving Enhanced Strength Retention at Elevated Temperatures in Ultrafine-Fibrous Interconnected Al-Ce-Ni Eutectic Alloy Solidified under Super-Gravity Field

Improve the ductility of a nickel based superalloy by optimizing secondary phase distribution through grain boundary engineering

Effect of long-term aging treatment on the tensile strength and ductility of GH 605 superalloy

Effects of Microstructure Evolution on the Deformation Mechanisms and Tensile Properties of a New Ni-base Superalloy During Aging at 800 °C

Microstructure Optimization for Higher Strength of a New Fe–Ni-based Superalloy

Evolution of Microstructures and Properties of the GH4169 Superalloy During Short-Term and High-Temperature Processing

Microstructural Evolution and Deformation Behavior of a Fe-Ni Base Superalloy During Aging

Effect of Μ Precipitation and Γ′ Evolution on Intra/intergranular Strength of Ni-Co-Cr-based Superalloys after 800 ℃ Thermal Exposure

Effect of μ precipitation and γ′ evolution on intra/intergranular strength of Ni-Co-Cr-based superalloys after 800 °C thermal exposure

Microstructural evolution of GH4079 superalloy during hot deformation and heat treatment

Identification of Precipitates in the As-cast Microstructure and Its Dissolution Behavior During Homogenization of Difficult-to-Deform GH4141 Superalloy

Effect of Long-Term Aging on Microstructural Stability and Tensile Deformation of a Fe–Ni-based Superalloy

Control of Nanoscale Precipitation and Elimination of Intermediate-Temperature Embrittlement in Multicomponent High-Entropy Alloys

Overcoming high-temperature strength-ductility trade-off by combination deformation twinning of C11b and D022 superlattices in a Ni-Cr-W/Mo-based superalloy

New strategy to improve the overall performance of single-crystal superalloys by designing a bimodal γ′ precipitation microstructure