Abstract:Taking into account the local stresses resulting from the primary twinning with transformation strains, the competition between double twinning {10–11}–{10–12} and (10–12)–(–1012) (CDTW and EDTW) is theoretically modeled. Using electron backscatter diffraction technique, the statistical fractions, thickness-length ratios and their critical values of CDTW and EDTW within grains of as-cast AZ31 magnesium alloy sheets at the low strain stage of hot rolling processing are obtained to validate the theoretical results. In addition, the competition between the DTW and twin intersection are also discussed in detail. The results show that: (1) The secondary twin growth complies with the classical Hall-Petch relationship. Due to the difference in the driving forces resulting from different transformation strains between the primary extension and contraction twinning, the secondary extension twin of EDTW is more difficult to grow compared to that of CDTW for primary twin bands with small thickness-length ratios, which is contrary to the regulation for primary twin bands with large thickness-length ratios; (2) The greater the thickness-length ratio of the primary twinning is, the smaller the critical shear stress of the secondary twinning is. This is opposite to the effect of thickness-length ratio on the critical shear stress of the incident twinning in the twin intersection. It is indicated that the thickening of the primary twinning provides the higher driving force for the formation of DTW, however hinders the twin intersection more evidently; (3) Within coarse grains, at the low strain stage, the formation of DTW can dominantly induce dynamic recrystallization and continue plastic deformation, while the stress concentration resulting from the twin intersection is inclined to cause brittle fracture. Therefore, based on the effect of the local stress, the selection mechanism of the thickness-length ratio on the DTW and twin intersection is of great significance to determining the plastic performance of magnesium alloys during hot working. In the current study, massive control factors of the thickness-length ratio of the primary twinning are concluded, which provides some corresponding schemes of material design.

Effect of Induced Screw Twisted Strain on the Twin Orientation Regulation and the Ductility of Pre-Twined ZM21 Mg Alloys

The effects of orientation control via tension-compression on microstructural evolution and mechanical behavior of AZ31 Mg alloy sheet

Influence of In-Plane Simple Shear Strain on the Grain Orientation Regulation and Stretch Formability of Pre-twinned AZ31 Magnesium Alloy Sheet

Unveiling the ductility enhancement mechanisms in AZ31 magnesium alloy achieved via shear strain-assisted twin orientation regulation

Effect of multi-pass continuous screw twist extrusion process on microstructure evolution, texture, and mechanical properties of AZ31 magnesium alloy

On the Strengthening and Slip Activity of Mg-3Al-1Zn Alloy with Pre-Induced { 10 1 over Bar 2 } Twins

Evolution of deformation mechanisms and their orientation dependence in fine-grained Mg-3Gd during tension

Reasonable Utilization of {10-12} Twin for Optimizing Microstructure and Improving Mechanical Property in a Mg-Gd-Y Alloy

Enhanced Precipitation Strengthening of Extruded Mg-8 Wt.%al-0.5 Wt.%zn (AZ80) Magnesium Alloy by Extension Twinning

Dynamic Recrystallization, Texture Evolution, and Improved Mechanical Properties of Mg-Y-Zn-V Alloy during Forging and Subsequent Extruding Deformation

Effect of pre-deformation on the activation stress of {10–12} twinning in Mg–3Al–1Zn alloy

Effect of Zn addition combined a novel screw twist extrusion technology on the microstructure, texture as well as the ductility of Mg-xZn-1Mn alloys

On the Strengthening and Slip Activity of Mg-3Al-1Zn Alloy with Pre-Induced {101¯2} Twins

Role of {101‾2} Twinning in the Anisotropy and Asymmetry of AZ31 Magnesium Alloy under High Strain Rate Deformation

Twinning Effects on the Hot Deformation Behavior of AZ31 Mg Alloy

Effects of texture and twinning on the torsional behavior of magnesium alloy solid rod: A crystal plasticity approach in comparison with uniaxial tension/compression

Improving mechanical properties of AZ31 alloy sheets via novel turned-bearing extrusion by introducing shear strain

Ductility Improvement by Twinning and Twin–slip Interaction in a Mg-Y Alloy

On the strengthening and slip activity of Mg-3Al-1Zn alloy with pre-induced { 10 1 ̄ 2 } twins

Effect of Local Stresses of Primary Twinning on Double Twinning, Twin Intersection and Their Competition

Effects of Deformation Mechanisms on Texture Evolution and Mechanical Response of the Mg-1Al-0.5Mn-0.3Gd Alloy Under Plane Tension