Abstract:Repetitive upsetting-extrusion (RUE) is known as a processing method that effectively improves the properties of a billet without changing its initial shape. In this paper, one pass RUE with reduced deformation temperature (re-upsetting at 360 °C and secondary extrusion at 340 °C) and different extrusion speeds (0.5 and 1 mm/s) is implemented to improve the strength and toughness of AZ80 Mg rods, and simultaneous reduction in tensile anisotropy is achieved. Influences of one pass RUE method on the resulting microstructure and texture evolution of the alloy are investigated alongside their correlated impact on its mechanical properties. After RUE processing, the grain structure of AZ80 alloy is characterized by numerous fine dynamic recrystallized (DRXed) grains, combined with large unDRXed grains obtained at high extrusion speed or coarse DRXed grain bands obtained at low extrusion speed. Besides, β-Mg17Al12 particles dynamically precipitated during deformation, acting as strong barrier against grain boundary migration through pinning effect. Through introduction of an interactive stress state, the RUE process promotes dispersion of the fiber texture that typically develops during the extrusion process. The key factor that promotes weakening of the fiber texture is derived from the refinement of basal orientated deformed grains, which form during upsetting deformation, into numerous non-basal orientated DRXed grains during early-stage extrusion. Compared with coarse deformed grains, these fine DRXed grains delay transformation of texture into the typical [10-10]–[11-20] fiber component. Grain refinement is implicated as the most significant factor with respect to simultaneous improvement of strength and toughness in the extruded rods, while tensile yield anisotropy in response to loading along the ED and TD is attributed to unDRXed grains with [10-10] fiber orientation. Compared to the as-cast state, extruded rods demonstrate increases in yield strength, ultimate tension strength, and elongation maximally up to ~2.6, ~2.2, and ~4.9 times, respectively. And when complete DRX structure is nearly achieved, the tensile yield anisotropy of extruded bar is effectively eliminated because the refined grains with relatively dispersed orientation inhibit the nucleation of tension twin and simultaneous enhance the Hall-Petch effect.

Effect of multi-pass continuous screw twist extrusion process on microstructure evolution, texture, and mechanical properties of AZ31 magnesium alloy

Deformation behaviour, microstructure evolution and dynamic recrystallization mechanism of AZ31 magnesium alloy under co-extruded by Mg-Al composite billet

Effect of Zn addition combined a novel screw twist extrusion technology on the microstructure, texture as well as the ductility of Mg-xZn-1Mn alloys

Dynamic Recrystallization, Texture Evolution, and Improved Mechanical Properties of Mg-Y-Zn-V Alloy during Forging and Subsequent Extruding Deformation

A novel continues multi-shear extrusion process on the microstructure and mechanical property evolution of AZ31 magnesium alloys

Effects of optimizing continuous forging extrusion process on the microstructure and mechanical properties of AZ31 magnesium alloy

Study of the microstructure, texture and tensile properties of as-extruded AZ91 magnesium alloy

Evolution of Microstructure and Tensile Properties of Extruded Mg-4Zn-1Y Alloy

Role of Grain Refinement Mechanism on Microstructure and Performance in AZ31B Alloy During Interactive Alternating Forward Extrusion (AFE) Process

The improvement of grain refinement, texture modification and mechanical properties of pure Mg prepared by cyclic expansion extrusion with an asymmetric extrusion cavity

Effects of Direct Extrusion Process on Microstructure, Texture Evolution and Yield Strength of Magnesium Alloy Az31

Microstructure, Texture and Mechanical Properties of Extruded AZ31 Mg Alloy During Small Strain Multi-Directional Forging with Gradient Cooling

The microstructure evolution, texture weakening mechanism and mechanical properties of AZ80 Mg alloy processed by repetitive upsetting-extrusion with reduced deformation temperature

Microstructure and texture evolution during compression-extrusion process for tension/compression symmetrical ZK61 magnesium alloy rod

Effect of Extrusion Parameters on Microstructure and Mechanical Properties of Mg-7.5Gd-2.5Y-3.5Zn-0.9Ca-0.4Zr (wt%) Alloy

Effect of Extrusion on Mechanical Properties of AZ91 Cast Magnesium Alloy

Thermomechanical Processing and Superplasticity of AZ91 Magnesium Alloy

Unveiling the microstructure evolution and deformation mechanisms of micro-alloying Mg-1.5Zn-0.5Zr-0.5Sr alloy via extrusion-shearing

Analysis of Abnormal Texture Formation and Strengthening Mechanism in an Extruded Mg-Gd-Y-Zn-Zr Alloy

The Dynamic Recrystallization and Mechanical Property Responses During Hot Screw Rolling on Pre-Aged ZM61 Magnesium Alloys

Grain refinement and improved mechanical properties of Mg-4Zn-0.5Ca-0.5RE magnesium alloy by thermomechanical processing