Abstract:The user demands for Lithium ion batteries in mobile applications and electric vehicles request steady improvement in terms of capacity and cycle life. State-of-the-art lithium ion batteries irreversibly loose about 10 % of the capacity during the first cycles due to SEI formation. Therefore, 10 % of the cathode material is not used during the rest of the cells life which results in a waste of cathode material and leads to a lowered range of battery electric vehicles. Therefore, these losses must be compensated to ensure efficient resource utilization and to further increase the capacity of the lithium ion battery. We have developed a method to compensate these capacity losses by pre-lithiation: A fast and simple approach of electrolyte-free direct contact pre-lithiation leads to targeted degrees of pre-lithiation in a range of 7-50 % for state-of-the-art graphite electrodes. The parameters pressure (0-40 MPa), temperature (20-150°C) and time (0-60 min) are used to transfer lithium from a temporary substrate to the graphite anode. This process uses 1-5 μm thin lithium films made by the Fraunhofer IWS lithium melt deposition process as a lithium source. [1] The degree of pre-lithiation can be controlled by the lithium loading of the temporary substrate. NCM full cells built with pre-lithiated graphite electrodes where electrochemically evaluated in comparison to unlithiated electrodes. They show 6.5 % capacity increase after the first cycles using the additional lithium to form the SEI during the first cycles. The parameter influence of the pre-lithiation process on the initial coulomb efficiency of cells with pre-lithiated graphite electrodes is examined in half cells showing an ICE of 99.91 % for the best parameters. This method of electrolyte-free direct contact pre-lithiation shows an efficient way to further increase the capacity of state-of-the-art LIBs with graphite electrodes by increasing the cathode material utilization. It can potentially be scaled up to a roll-to-roll process using a heated calender nip. The temporary substrates with tailored lithium loading can be processed by lithium melt deposition in an efficient way with high lithium yield and high precision. [1] K. Schönherr, B. Schumm, F. Hippauf, R. Lissy, H. Althues, C. Leyens, S. Kaskel, Chemical Engineering Journal Advances 2022 , 9 , 100218. Figure 1

Lithiophilic Chemistry Facilitated Ultrathin Lithium for Scalable Prelithiation

Non-destructive Chemical Prelithiation of VO2(B) Anodes Constructing a Multifunctional Interphase Layer for Advanced Li-Ion Batteries

A Large-Area Lithium Metal-Carbon Nanotube Film for Precise Contact Prelithiation in Lithium-Ion Batteries

Large-Area Lithium Metal-Carbon Nanotube Film for Precise Contact Prelithiation in Lithium-ion Batteries

Modulating Lithium Nucleation Behavior Through Ultrathin Interfacial Layer for Superior Lithium Metal Batteries

Sustainable Prelithiation Strategy: Enhancing Energy Density and Lifespan with Ultrathin Li‐Mg‐Al Alloy Foil

Ultralight PEDOT Functionalized Separators Toward High‐Performance Lithium Metal Anodes

Roll-to-roll Prelithiation of Lithium-Ion Battery Anodes by Transfer Printing

Tailored Pre-Lithiation of Carbon Anodes Using Melt Deposited Thin Lithium

Achieving Desirable Initial Coulombic Efficiencies and Full Capacity Utilization of Li‐Ion Batteries by Chemical Prelithiation of Graphite Anode

Endowing Cu Foil Self-Wettable in Molten Lithium: A Roll-to-Roll Wet Coating Strategy to Fabricate High-Performance Ultrathin Lithium Metal Anodes

A Highly Effective and Controllable Chemical Prelithiation of Silicon/Carbon/Graphite Composite Anodes for Lithium-Ion Batteries

Realizing Ultrathin LiSn Alloy Anode by Tuning the Wettability of Molten Li for High-Energy-Density Batteries

Practical Prelithiation of 4.5 V LiCoO2||Graphite Batteries by a Passivated Lithium-Carbon Composite

Mechanically Robust Current Collector with Gradient Lithiophilicity Induced by Spontaneous Lithium Ion Diffusion for Stable Lean-Lithium Metal Batteries

A Thin‐Layer, Li+ Compensation, Moisture‐Tolerant Interfacial Modification of Cu Substrate Toward the Anode‐Less, Energy/Power Dense Li Metallic Batteries

Roll-to-roll fabrication of lithium metal anodes with hierarchical lithiophilic structures and controlled deposition for enhanced stability

A High-Efficient Stable Surface-Prelithiated Li1.2ni0.13co0.13mn0.54o2 Cathode Enabled by Sacrificial Lithium Nitrides for High-Energy-Density Lithium-Ion Batteries

Preparation, Processing, and Application of Ultrathin Lithium Metal

Scalable Production of Thin and Durable Practical Li Metal Anode for High‐Energy‐Density Batteries

Non-destructive chemical prelithiation of VO 2 (B) anodes constructing a multifunctional interphase layer for advanced Li-Ion batteries