Abstract:Metallic Li, with ultrahigh theoretical capacity (3860 mA h g−1) and the lowest electrochemical potential (−3.04 V vs. the standard hydrogen electrode), is perfectly meet the needs of high energy density lithium batteries. However, the direct use of metallic lithium as anode would cause serious dendrite and huge volume expansion, which will bring safety hazards and restrict the practical commercialization of Li metal anodes. Herein, a facile electrophoretic deposition (EPD) method was employed for the first time to fabricate uniform TiN modified commercial Cu foam ( foam) as the lithiophilic 3D conductive skeleton. The lithiophilic TiN acts as the well-distributed seeds to promote the uniform lithium deposition, attributing to the lowed nucleation overpotential. The porous and conductive Cu foams can further mitigate the formation of Li dendrites, on account of its high specific surface area reduce the effective current density. The foam based half cells and symmetric cells both exhibit improved reversibility and reduced polarization voltage in lithium plating/stripping process. Furthermore, better rate performance and cycling stability were also achieved in the full-cell configurations of foam-Li/Li4Ti5O12 (LTO) and foam-Li/LiFePO4 (LFP). This work demonstrates a facile strategy to modify the commercial current collectors with pre-synthesized lithiophilic nanoparticles for achieving uniform Li deposition.

Endowing Cu Foil Self-Wettable in Molten Lithium: A Roll-to-Roll Wet Coating Strategy to Fabricate High-Performance Ultrathin Lithium Metal Anodes

Melting lithium alloying to improve the affinity of Cu foil for ultra-thin lithium metal anode

Tuning wettability of molten lithium via a chemical strategy for lithium metal anodes

Roll-to-roll fabrication of lithium metal anodes with hierarchical lithiophilic structures and controlled deposition for enhanced stability

A Thin‐Layer, Li+ Compensation, Moisture‐Tolerant Interfacial Modification of Cu Substrate Toward the Anode‐Less, Energy/Power Dense Li Metallic Batteries

Realizing Ultrathin LiSn Alloy Anode by Tuning the Wettability of Molten Li for High-Energy-Density Batteries

Mechanical rolling formation of interpenetrated lithium metal/lithium tin alloy foil for ultrahigh-rate battery anode

Lithiophilic Coating Layer Modify Three-Dimensional Cu Foam for Stable and Dendrite-Free Lithium Metal Anode

Dendrite-free Sandwiched Ultrathin Lithium Metal Anode with Even Lithium Plating and Stripping Behavior

Scalable Production of Thin and Durable Practical Li Metal Anode for High‐Energy‐Density Batteries

LiCoO 2 Ultrathin Layer for Uniform Lithium Deposition toward a Highly Stable Lithium Metal Anode

Constructing an Inorganic/organic Mixed Protective Film for Low-Cost Fabrication of Stable Lithium Metal Anode

Ultrasmooth and Dense Lithium Deposition Toward High-Performance Lithium-Metal Batteries

LiI/Cu Mixed Conductive Interface Via the Mechanical Rolling Approach for Stable Lithium Anodes in the Carbonate Electrolyte.

Ultrathin Li-rich Li-Cu alloy anode capped with lithiophilic LiC6 headspace enabling stable cyclic performance

Coating Highly Lithiophilic Zn on Cu Foil for High-Performance Lithium Metal Batteries

Coordinating Ionic and Electronic Conductivity on 3D Porous Host Enabling Deep Dense Lithium Deposition Toward High-Capacity Lithium Metal Anodes

Uniform titanium nitride decorated Cu foams by electrophoretic deposition for stable lithium metal anodes

Uniform Li Deposition by Regulating the Initial Nucleation Barrierviaa Simple Liquid-Metal Coating for a Dendrite-Free Li–metal Anode

Coordinating ionic and electronic conductivity on 3D porous host enabling deep dense lithium deposition toward high-capacity lithium metal anode

Facile decoration of fluorinated metal-organic frameworks on copper foil for regulated lithium deposition and robust solid electrolyte interface