Abstract:While self-supporting Al foil anode has high theoretical capacity and appropriate potential for Li-ion batteries, the poor initial Coulombic efficiency (ICE) retards its wide industrial applications, making prelithiation necessary. Herein, we develop a facile and efficient mechanical prelithiation (MP) approach suitable for mass production. Even though ICE was improved from 70% to 90% after MP, the cycling performance is still deficient, which we attribute to the insufficient density of grain boundaries that leads to poor lithiation/delithiation ductility (LDD), characterized by the rapid loss in electronic percolation across the foil. As a classic strategy in metallurgy to tune the grain boundaries, thermal annealing and recrystallization is further exploited to optimize the LDD of Al foil. For standard Al foil, whose grain size is big with lots of dislocations inside, MP followed by electrochemical cycling causes cracking, electrolyte infiltration and SEI formation. Its electronic percolation (damage) is monitored in real time, and is found to decay rapidly as the insulating SEI blocked all the electron transport paths of one grain (or a cluster of grains). But if MP takes place after annealing standard Al foil at 300°C for 15min, the dislocations recombined to achieve refined grains whose sharp GB network can slide effectively to relieve stress buildup due to phase transitions and suppress deep crack development, and the prelithiated foil achieved superior electrochemical performance, with significant life extension in the in-plane electronic conductance. However, interestingly, upon further increase in the annealing temperature, as the grain size turns bigger, the electrochemical performance of prelithiated foil deteriorates. Based on the comparison of the microstructures and electrochemical performance at different thermal annealing conditions, we found that the GB density before MP plays an essential role in the stress relief and keeping electronic percolation during cycling. Our optimized prelithiated Al foil maintains 80% capacity retention after 100 cycles in LiFePO4//LiAly full cell with 1.8× excess lithium. It cycles significantly better than pure LiBCC foil of equal thickness (65μm), especially in lean-electrolyte condition, suggesting such safe, cheap and high energy density metallic foil anodes deserve comparable attention as pure lithium metal anode.

Sustainable Prelithiation Strategy: Enhancing Energy Density and Lifespan with Ultrathin Li‐Mg‐Al Alloy Foil

Non-destructive Chemical Prelithiation of VO2(B) Anodes Constructing a Multifunctional Interphase Layer for Advanced Li-Ion Batteries

Enhancing the Cycle-Life of Initial-Anode-free Lithium-Metal Batteries by Pre-Lithiation in Mn-based Li-rich Spinel Cathodes

Advancing Anode-Less Lithium Metal Batteries: ZnF2 Modification and In-Situ Structural Regulation for Enhanced Performance

Single-material Aluminum Foil As Anodes Enabling High-Performance Lithium-Ion Batteries: the Roles of Prelithiation and Working Mechanism

A Functional Prelithiation Separator Promises Sustainable High‐Energy Lithium‐Ion Batteries

Optimal annealing of Al foil anode for prelithiation and full-cell cycling in Li-ion battery: The role of grain boundaries in lithiation/delithiation ductility

Prelithiation Enhances Cycling Life of Lithium-Ion Batteries: A Mini Review

Prolonged lifespan of initial-anode-free lithium-metal battery by pre-lithiation in Li-rich Li2Ni0.5Mn1.5O4 spinel cathode

Modulating Lithium Nucleation Behavior Through Ultrathin Interfacial Layer for Superior Lithium Metal Batteries

Dynamic Concentration of Alloying Element on Anode Surface Enabling Cycle‐Stable Li Metal Batteries

Prolonged Lifespan of Initial-Anode-free Lithium-Metal Battery by Pre-Lithiation in Li-rich Li2Ni0.5Mn1.5O4spinel Cathode

Tailoring the Passivation Layer on Lithium Metal Anode and Aluminum Collector by Regulating the Solvation Structure to Enhance the Long-Term Cycling of Lithium Metal Batteries

Progress and Challenges of Prelithiation Technology for Lithium‐ion Battery

Non-sticky Li-alloy leaves for long-lasting secondary batteries

Prelithiation: A Critical Strategy Towards Practical Application of High‐Energy‐Density Batteries

Activated nanolithia as an effective prelithiation additive for lithium-ion batteries

Advancements in Prelithiation Technology: Transforming Batteries from Li‐Shortage to Li‐Rich Systems

A Scalable and Controllable Li‐powder‐coating Pre‐lithiation Method toward Ultra‐long‐life and High‐energy‐density LiFePO4 Battery

Enhancing lithium-metal battery longevity through minimized coordinating diluent

Lithiophilic Chemistry Facilitated Ultrathin Lithium for Scalable Prelithiation