Abstract:Prelithiation is a well-established strategy for enhancing battery energy density. However, traditional prelithiation approaches have primarily addressed compensating for the initial active lithium loss (ALL) while overlooking the ALL during extended cycling. In response, a novel method is introduced by increasing the prelithiation degree and pre-storing stable LiCx within the anode. This innovation facilitates sustainable lithium replenishment, resulting in a significant improvement in battery cycle life and energy density. Moreover, challenges associated with using pure Li foils to realize this strategy in contact prelithiation are revealed, such as difficulties in thinning to less than 5 mu m, and the loss of the electronic pathway during prelithiation, resulting in low lithium utilization rates and numerous residues. Additionally, the significantly accelerated capacity fading caused by these residues, typically emerging after hundreds of cycles, has been overlooked. To overcome these challenges, an ultrathin Li-Mg-Al alloy foil is developed with significantly improved mechanical properties and delithiation behavior. During prelithiation, the 96Li2Mg2Al alloy maintains a complete film structure with numerous micropores, avoiding randomly distributed debris. This structure ensures high utilization, unimpeded electronic pathways, and efficient electrolyte filtration. By employing a 5-mu m 96Li2Mg2Al foil for sustainable prelithiation, a substantial improvement in energy density is achieved and tripled the battery's lifespan. A novel life-span prelithiation strategy is proposed and practiced through the replacement of fragile ultrathin lithium metal with self-supporting 96Li2Mg2Al alloys which can spontaneously form a macroscopically complete but microscopically porous membrane after delithiation. This study provides a new perspective on the design of competitive prelithiated batteries and prompts a reevaluation of the potential negative impacts of the current prelithiation method. image

A Scalable and Controllable Li‐powder‐coating Pre‐lithiation Method toward Ultra‐long‐life and High‐energy‐density LiFePO4 Battery

Non-destructive Chemical Prelithiation of VO2(B) Anodes Constructing a Multifunctional Interphase Layer for Advanced Li-Ion Batteries

Controllable Long-term Lithium Replenishment for Enhancing Energy Density and Cycle Life of Lithium-ion Batteries

Feasibility of Prelithiation in LiFePO4

Practical Prelithiation of 4.5 V LiCoO2||Graphite Batteries by a Passivated Lithium-Carbon Composite

Practical Prelithiation of 4.5 V LiCoO 2 ||Graphite Batteries by a Passivated Lithium‐Carbon Composite

Organophosphorus Hybrid Solid Electrolyte Interphase Layer Based on LixPO4 Enables Uniform Lithium Deposition for High‐Performance Lithium Metal Batteries

Offsetting Initial Lithium Loss By Pre-Forming SEI Layer on Graphite Surface

Achieving Sei Preformed Graphite in Flow Cell to Mitigate Initial Lithium Loss

Ultralong-life lithium metal batteries enabled by decorating robust hybrid interphases on 3D layered framworks

Organophosphorus Hybrid Solid Electrolyte Interphase Layer Based on Li x PO 4 Enables Uniform Lithium Deposition for High‐Performance Lithium Metal Batteries

Sustainable Prelithiation Strategy: Enhancing Energy Density and Lifespan with Ultrathin Li‐Mg‐Al Alloy Foil

Scalable Process for Application of Stabilized Lithium Metal Powder in Li-ion Batteries

Low-Cost Al2o3 Coating Layer As A Preformed Sei on Natural Graphite Powder to Improve Coulombic Efficiency and High-Rate Cycling Stability of Lithium-Ion Batteries

Elongating the Cycle Life of Lithium Metal Batteries in Carbonate Electrolyte with Gradient Solid Electrolyte Interphase Layer

A Sustainable Solid Electrolyte Interphase for High‐Energy‐Density Lithium Metal Batteries under Practical Conditions

Improving the Performance of A Lifepo4 Cathode Based on Electrochemically Cleaved Graphite Oxides with High Hydrophilicity and Good Conductivity

Addressing the initial lithium loss of lithium ion batteries by introducing pre-lithiation reagent Li5FeO4/C in the cathode side

In situ Construction of Robust Biphasic Surface Layers on Lithium Metal for Lithium-Sulfide Batteries with Long Cycle Life

A Systematic Effect for an Ultra-long Cycle Lithium-sulfur Battery.

Long‐Life Lithium‐Metal All‐Solid‐State Batteries and Stable Li Plating Enabled by In‐situ Formation of Li3PS4 in SEI Layer