Abstract:The user demands for Lithium ion batteries in mobile applications and electric vehicles request steady improvement in terms of capacity and cycle life. State-of-the-art lithium ion batteries irreversibly loose about 10 % of the capacity during the first cycles due to SEI formation. Therefore, 10 % of the cathode material is not used during the rest of the cells life which results in a waste of cathode material and leads to a lowered range of battery electric vehicles. Therefore, these losses must be compensated to ensure efficient resource utilization and to further increase the capacity of the lithium ion battery. We have developed a method to compensate these capacity losses by pre-lithiation: A fast and simple approach of electrolyte-free direct contact pre-lithiation leads to targeted degrees of pre-lithiation in a range of 7-50 % for state-of-the-art graphite electrodes. The parameters pressure (0-40 MPa), temperature (20-150°C) and time (0-60 min) are used to transfer lithium from a temporary substrate to the graphite anode. This process uses 1-5 μm thin lithium films made by the Fraunhofer IWS lithium melt deposition process as a lithium source. [1] The degree of pre-lithiation can be controlled by the lithium loading of the temporary substrate. NCM full cells built with pre-lithiated graphite electrodes where electrochemically evaluated in comparison to unlithiated electrodes. They show 6.5 % capacity increase after the first cycles using the additional lithium to form the SEI during the first cycles. The parameter influence of the pre-lithiation process on the initial coulomb efficiency of cells with pre-lithiated graphite electrodes is examined in half cells showing an ICE of 99.91 % for the best parameters. This method of electrolyte-free direct contact pre-lithiation shows an efficient way to further increase the capacity of state-of-the-art LIBs with graphite electrodes by increasing the cathode material utilization. It can potentially be scaled up to a roll-to-roll process using a heated calender nip. The temporary substrates with tailored lithium loading can be processed by lithium melt deposition in an efficient way with high lithium yield and high precision. [1] K. Schönherr, B. Schumm, F. Hippauf, R. Lissy, H. Althues, C. Leyens, S. Kaskel, Chemical Engineering Journal Advances 2022 , 9 , 100218. Figure 1

Offsetting Initial Lithium Loss By Pre-Forming SEI Layer on Graphite Surface

Achieving Sei Preformed Graphite in Flow Cell to Mitigate Initial Lithium Loss

Tailored Pre-Lithiation of Carbon Anodes Using Melt Deposited Thin Lithium

Non-destructive Chemical Prelithiation of VO2(B) Anodes Constructing a Multifunctional Interphase Layer for Advanced Li-Ion Batteries

A Bifunctional Composite Artificial Solid Electrolyte Interphase for High Stable Solid-State Lithium Batteries

Interphase Engineering Enhanced Electro‐chemical Stability of Prelithiated Anode

Tailored Pre-Lithiation Using Melt-Deposited Lithium Thin Films

High-capacity battery cathode prelithiation to offset initial lithium loss

Addressing the initial lithium loss of lithium ion batteries by introducing pre-lithiation reagent Li5FeO4/C in the cathode side

A Scalable and Controllable Li‐powder‐coating Pre‐lithiation Method toward Ultra‐long‐life and High‐energy‐density LiFePO4 Battery

Insight into the Enforced Stability of the Solid Electrolyte Interphase on the Graphite Anode by Prelithiation

Controllable solid electrolyte interphase precursor for stabilizing natural graphite anode in lithium ion batteries

Facilitating prelithiation of silicon carbon anode by localized high‐concentration electrolyte for high‐rate and long‐cycle lithium storage

Impact of Electrolyte on Direct-Contact Prelithiation of Silicon-Graphite Anodes in Lithium-Ion Cells with High-Nickel Cathodes

Molecular Engineering Chemical Pre‐lithiation Reagent with Low Redox Potential for Graphite Anode Enables High Coulombic Efficiency

Promoting the reversibility of lithium ion/lithium metal hybrid graphite anode by regulating solid electrolyte interface

Eliminating Graphite Exfoliation with an Artificial Solid Electrolyte Interphase for Stable Lithium‐Ion Batteries

A High-Efficient Stable Surface-Prelithiated Li1.2ni0.13co0.13mn0.54o2 Cathode Enabled by Sacrificial Lithium Nitrides for High-Energy-Density Lithium-Ion Batteries

LiF/Fe composite for Ni-rich cathode prelithiation: Synthesis, bilayer structured electrode and lithium loss compensation

Highly Efficient Interface Modification between Poly(Propylene Carbonate)-Based Solid Electrolytes and a Lithium Anode by Facile Graphite Coating

Interfacial Fluoride Engineering Enabled Robust LiF-rich Solid Electrolyte Interphase to Reduce Active Lithium Loss in Rechargeable Lithium Battery