Abstract:ZrB2-SiC-Zr2Al4C5 multi-phase ceramics with uniform structure and high density were successfully prepared through the introduction of in situ synthesized Zr2Al4C5 into ZrB2-SiC ceramic via SPS at 1800 °C. A systematic analysis and discussion of the experimental results and proposed mechanisms were carried out to demonstrate the composition-dependent sintering properties, mechanical properties and oxidation behavior. The results showed that the in situ synthesized Zr2Al4C5 could be evenly distributed in the ZrB2-SiC ceramic matrix and inhibited the growth of ZrB2 grains, which played a positive role in the sintering densification of the composite ceramics. With increasing Zr2Al4C5 content, the Vickers hardness and Young's modulus of composite ceramics gradually decreased. The fracture toughness showed a trend that first increased and then decreased, and was increased by about 30% compared with ZrB2-SiC ceramics. The major phases resulting from the oxidation of samples were ZrO2, ZrSiO4, aluminosilicate and SiO2 glass. With increasing Zr2Al4C5 content, the oxidative weight showed a trend that first increased then decreased; the composite ceramic with 30 vol.% Zr2Al4C5 showed the smallest oxidative weight gain. We believe that the presence of Zr2Al4C5 results in the formation of Al2O3 during the oxidation process, subsequently resulting in a lowering of the viscosity of the glassy silica scale, which in turn intensifies the oxidation of the composite ceramics. This would also increase oxygen permeation through the scale, adversely affecting the oxidation resistance of the composites with high Zr2Al4C5 content.

Effect of copper phosphate on the sintering and ablation resistance of novel ZrSiO4 based composites

Enhanced ablative resistance of C/C composites with densified ZrB 2 -based ceramics by incorporation of Mo as interface layer

Microstructure evolution and ablation mechanisms of Csf/ZrB2-SiC composites at different heat fluxes under air plasma flame

The effects of ZrSi 2 on the ablation and insulation performances of low-density carbon-phenolic composites

Mechanical, Corrosion and Wear Characteristics of Cu-Based Composites Reinforced with Zirconium Diboride Consolidated by SPS

SPS densification and ablative performance of ZrB2–SiC–ZrC composites derived from the ternary powders by sol-gel

Mechanical, Wetting and Corrosion Properties of a Zr-based Amorphous Alloy Composite Consolidated by Spark Plasma Sintering

Structural characteristics and ablative behavior of C/C–ZrC–SiC composites reinforced with “Z-pins like” Zr–Si–B–C multiphase ceramic rods

Ablation resistance of ZrB2–SiC–AlN ceramic composites

Modification of SiBCN by Zr Atom and Its Effect on Ablative Resistance of Cf/SiBCN(Zr) Composites

The effects of zirconium diboride particles on the ablation performance of carbon-phenolic composites under an oxyacetylene flame

Preparation and flame ablation/oxidation behavior of ZrB2/SiC ultra-high temperature ceramic composites

Oxidation behavior and ablation mechanism of Cf/ZrB2-SiC composite fabricated by vibration-assisted slurry impregnation combined with low-temperature hot pressing

Thermal ablation behavior of SiBCN-Zr composites prepared by reactive spark plasma sintering

Effect of Zr2Al4C5 Content on the Mechanical Properties and Oxidation Behavior of ZrB2-SiC-Zr2Al4C5 Ceramics

Ablation Behavior and Mechanism of (Pyc-Csf)/zrb2-sic-zrc Ceramics Sintered by Reactive Spark Plasma Sintering at Low Temperature

Ablation behavior and mechanisms of ZrC-SiC-MoSi2 coated C/C-SiC-ZrC ceramic matrix composites under oxyacetylene torch

SPS Sintering Behavior and Microstructure of ZrB2-SiCpl Composite Ceramics

Cold-Sintered ZnO Ceramic Composites Co-Doped with Polytetrafluoroethylene and Oxides

Effect of ZrN-Sialon Composite Powder on Properties of Al2O3-C Refractory

Ablation-resistance of ZrB2-SiC Coating under Oxygen-propane Torch Flame Prepared by Atmospheric Plasma Spraying